Diagnose soonWrong pressure - real or reported - can burn clutches fast; do not keep driving hard on this code.
Your transmission's B pressure reading does not add up - either the sensor is lying or the actual fluid pressure is wrong. Either way, shift quality suffers.
Key facts
P0846 means transmission fluid pressure sensor/switch B circuit range/performance. Your transmission's B pressure reading does not add up - either the sensor is lying or the actual fluid pressure is wrong. Either way, shift quality suffers. WrenchFair's published fair-price range for this repair is $80–$400 parts and $200–$500 labor at independent shops.
WrenchFair rates P0846 a 4-of-5 DIY difficulty (“Live-data pressure readings separate sensor faults from real hydraulic problems.”) with a “Diagnose soon” driveability rating: Wrong pressure - real or reported - can burn clutches fast; do not keep driving hard on this code. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 580 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Power Train) — see the latest ones
On your 2013–2018 Nissan Altima (2.5L QR25DE + Jatco CVT) — CVT fluid service:Owner-verified
Vehicle-specific service procedure. The L33 Altima CVT (Jatco CVT8 / JF016E) has NO dipstick — the underhood 'cap' is a sealed charge-pipe cap, not a gauge. Fill through the charge pipe/fill plug, then verify level from underneath with the engine running, transmission at ~104°F (40°C), on level ground: remove the overflow plug and a steady trickle (~one drip per second) means the level is correct.
Do this test first: Check for TSBs and companion codes; diagnose power faults first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0846 on the 2013–2018 Nissan Altima — but the community-sourced CVT fluid service note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
CVT oil pan bolts: 7.9 N·m (70 in-lb) — From Nissan TSB NTB16-110o covering 2013-2017 Altima JF016E (RE0F10D) valve-body work; existing bolts are reused.
CVT drain plug: verify — Confirm against Nissan factory service info. Generic Nissan drain-plug guidance cites ~25 ft-lb but is not verified for this aluminum CVT pan.
Overflow/level-check plug: verify — Confirm against Nissan factory service info. 14mm plug reported in owner how-tos; torque value not verified.
Tips
NS-3 ONLY. The 2013 Altima owner's manual (page 385) states: 'Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT, which is not covered by the NISSAN new vehicle limited warranty.' Wrong fluid (e.g. conventional ATF) can require two back-to-back drain-and-fills to correct.
Drain-and-fill beats power-flush in the owner consensus. NicoClub/BITOG owners and a Nissan master tech favor repeated drain-and-fills (roughly every 30k miles) over machine flushes; one Nissan tech warns that servicing a trans whose 30k/60k services were skipped can dislodge deposits and cause problems, and a shop owner quoted on forums says 'DO NOT let anyone flush the transmission. Have the trans pan dropped.' Caveat: one well-regarded NicoClub member disputes the flush-kills myth, noting the pump-driven exchange is gentle and neglected units were likely failing anyway — so treat this as contested, not gospel.
Level check is temperature-critical: no dipstick exists. Nissan tech guidance: warm the CVT to ~104°F (40°C), engine running, car level, pull the overflow plug at the pan bottom; fluid trickling out (about one drip per second) = correct level. Overfilling causes pressure issues.
Measure what drains out and refill the same amount, then verify with the overflow-plug procedure. A simple drain-and-fill typically takes ~5-6 quarts of NS-3 (owners report ~6 quarts in DIY videos); buy six quarts and expect a top-off.
Two filters exist and both are serviceable with the pan down: the pan strainer (Nissan part 31728-1XF03, 3-bolt screen) and the cartridge filter (31726-28X0A) behind a side cover. That said, a NicoClub technical expert (2013 Altima owner) notes CVTs don't load filters with clutch material like conventional automatics, so if fluid is kept fresh the filters rarely need changing — a pan drop around 60k 'won't hurt' if you're ambitious, but most owners just do drain-and-fills.
After the service, a scan tool is used to reset the CVT fluid deterioration data in the TCM so the car tracks fresh fluid life.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
harsh or slipping shifts
transmission overheating
limp mode
check-engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Real hydraulic pressure problem - low fluid, weak pump, stuck valve (most common) 9 owner notes link this repair to P0846
Failed pressure sensor/switch B reading out of range 9 owner notes link this repair to P0846
Corroded connector skewing the signal
Blocked hydraulic passage or restricted filter 9 owner notes link this repair to P0846
Failed PCM/TCM (rare)
Owner notes linked to P0846: 9 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for TSBs and companion codes; diagnose power faults first.
Check fluid level and condition - low fluid causes real pressure problems that mimic sensor faults. Tests: Real hydraulic pressure problem - low fluid, weak pump, stuck valve (most common)
Watch the B-circuit pressure reading on scan-tool live data during shifts. Tests: Failed pressure sensor/switch B reading out of range
Test line pressure with a manual gauge at the transmission test port if the reading looks wrong. Tests: Failed pressure sensor/switch B reading out of range
Inspect the sensor connector and wiring for corrosion before condemning the sensor.
If pressure is truly wrong, suspect the pump, a stuck valve, or internal leaks - specialist territory.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2018 Nissan Altima: CVT fluid service — test first, then buy for this job.
The price range below is a national planning range for P0846 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$80 – $400
Labor$200 – $500
Transmission fluid pressure sensor/switch replacement or valve-body service. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0846 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Live-data pressure readings separate sensor faults from real hydraulic problems.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →