P0336

P0336: Crankshaft position sensor A circuit range/performance

For your specific vehicle: P0336 on a 2020–2020 Buick Encore GX · 2001–2006 GMC 2500

DIY difficulty 2/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Can I drive with P0336?

Can I drive with a P0336 code?

Short trips and gentle driving only, until you know the cause. The car can stall without warning - avoid heavy traffic and get it fixed soon. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.

How serious is P0336?

Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. The car can stall without warning - avoid heavy traffic and get it fixed soon.

Will P0336 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

The sensor tracking crankshaft position is cutting out - typically when hot. Classic symptom: the car dies and won't restart until it cools down.

VW/Audi note (VCDS): Log engine RPM during cranking - no RPM signal while cranking means the crank sensor.
Model notes: On a high-mileage car, keep a spare crank sensor in the trunk - when it dies hot, you walk.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 2 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Note whether failure is heat-related - the signature of a dying sensor Tests: Failing crank sensor (heat-sensitive)
  2. Check the air gap and reluctor for damage Tests: Damaged reluctor ring

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$30 – $100
Labor$80 – $200

One bolt and a connector, though access can be awkward. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0336 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Access can be awkward but it is one bolt.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: Sensor mounting bolts: typically 8–12 Nm — verify spec. Never overtighten sensors with plastic bodies.

Pro tip: Check wiring and connectors first — chafed wires and corroded pins cause more sensor codes than dead sensors do.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →