Community-sourced DIY repair guides for the 2013–2018 Nissan Altima, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Spark plugs and ignition coils Owner-verified(2.5L QR25DE I4)
On the 2013-2018 Altima 2.5L the QR25DE's spark plugs sit on top of the engine under the plastic engine cover — no intake-manifold removal is needed (unlike the 3.5L V6, where the rear plugs are buried). Pop off the engine cover, unplug each ignition coil connector, remove the coil hold-down bolts with a 10mm socket, pull the coils straight up, then remove the plugs with a 9/16-inch spark plug socket. The same procedure fits 2012-2018 Altima 2.5L models.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Torque specs
Spark plugs (QR25DE): 14-22 ft-lb (20-29 N-m) — Nissan FSM engine-maintenance spec for the QR25DE; matches L33 plug-manufacturer data (20-25 N-m). Gap 1.1 mm (0.043 in), not adjustable — replace plugs as needed.
Ignition coil bolts: 48-65 in-lb (5.4-7.3 N-m) — Nissan FSM spec for the QR25DE; 10mm bolt heads. Snug only — overtightening cracks the coil.
Tips
If you find oil pooled in a spark plug well, the valve cover's spark-plug tube seals are leaking — on the QR25DE family these seals are molded into the valve cover, so the fix is a new valve cover/gasket, not just a dab of sealant.
Replace all four coils or at least carry a spare if you're past 150k miles; a weak coil shows up as a P030x misfire under load.
Use iridium OEM-spec plugs (NGK/Denso) — platinum/iridium tips, 4 required.
Front brake pads and rotors Owner-verified(2.5L QR25DE I4)
Front brakes are a single-piston floating caliper on slide pins. Remove the two slide-pin bolts with a 14mm socket, lift the caliper off, and hang it from the strut with wire or a hook — never let it dangle on the brake hose. The pads slide out of the bracket. To replace the rotor, remove the caliper bracket (torque member) bolts from behind the knuckle with a 19mm wrench/socket and lift the bracket off; the rotor then slides off the hub. After reassembly, pump the brake pedal several times before driving, and drive gently for the first ~30 miles to bed the pads in.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Caliper slide pin (caliper-to-bracket) bolts: 20 ft-lb — Confirmed by CarParts.com's 2013-2018 Altima front brake video and a Nissan tech's 2015 Altima spec sheet (20 ft-lb front).
Caliper bracket (torque member) to spindle bolts: 91 ft-lb — Nissan tech spec for the 2015 Altima SV (L33). These take real force — use a breaker bar to loosen.
Wheel lug nuts: verify — Confirm against factory service info for this vehicle.
Tips
Pull the slide pins, clean them, and relube with silicone-based brake grease — sticky pins are the most common cause of uneven pad wear on these cars.
The rotor often rust-welds to the hub; wire-brush the hub face before fitting the new rotor to avoid lateral runout.
Check the wear sensors: the video walkthrough notes wear bars were the tell on this generation.
The 12V battery is under the hood on the driver's side of the engine bay. With the engine off, loosen the negative (-) terminal bolt with a 10mm socket first and tuck the cable aside so it can't spring back, then loosen and remove the positive (+) terminal (flip open the red plastic cover first). Remove the hold-down clamp with a wrench or ratchet, lift the old battery straight out, set the new battery in, reinstall the hold-down, then reconnect in reverse order: positive (+) first, negative (-) last.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Torque specs
Battery terminal bolts and hold-down bolt: verify — Confirm against factory service info for this vehicle.
Tips
If the engine idles rough or stalls after reconnecting the battery, the ECM lost its idle air volume memory — perform Nissan's 'Idle Air Volume Learning' procedure (documented in the 2016 Altima FSM EC section): accelerator-pedal-release learning, throttle-valve-closed learning, warm engine to operating temp, then the pedal-timing sequence (or do it with a scan tool).
The 2013 Altima has push-button start models where a dead 12V battery can make the car not recognize the Intelligent Key — this is normal, not a fob failure.
Clean corrosion off the tray and terminals with a wire brush before fitting the new battery.
CVT fluid service Owner-verified(2.5L QR25DE + Jatco CVT)
Vehicle-specific service procedure. The L33 Altima CVT (Jatco CVT8 / JF016E) has NO dipstick — the underhood 'cap' is a sealed charge-pipe cap, not a gauge. Fill through the charge pipe/fill plug, then verify level from underneath with the engine running, transmission at ~104°F (40°C), on level ground: remove the overflow plug and a steady trickle (~one drip per second) means the level is correct.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
CVT oil pan bolts: 7.9 N·m (70 in-lb) — From Nissan TSB NTB16-110o covering 2013-2017 Altima JF016E (RE0F10D) valve-body work; existing bolts are reused.
CVT drain plug: verify — Confirm against Nissan factory service info. Generic Nissan drain-plug guidance cites ~25 ft-lb but is not verified for this aluminum CVT pan.
Overflow/level-check plug: verify — Confirm against Nissan factory service info. 14mm plug reported in owner how-tos; torque value not verified.
Tips
NS-3 ONLY. The 2013 Altima owner's manual (page 385) states: 'Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT, which is not covered by the NISSAN new vehicle limited warranty.' Wrong fluid (e.g. conventional ATF) can require two back-to-back drain-and-fills to correct.
Drain-and-fill beats power-flush in the owner consensus. NicoClub/BITOG owners and a Nissan master tech favor repeated drain-and-fills (roughly every 30k miles) over machine flushes; one Nissan tech warns that servicing a trans whose 30k/60k services were skipped can dislodge deposits and cause problems, and a shop owner quoted on forums says 'DO NOT let anyone flush the transmission. Have the trans pan dropped.' Caveat: one well-regarded NicoClub member disputes the flush-kills myth, noting the pump-driven exchange is gentle and neglected units were likely failing anyway — so treat this as contested, not gospel.
Level check is temperature-critical: no dipstick exists. Nissan tech guidance: warm the CVT to ~104°F (40°C), engine running, car level, pull the overflow plug at the pan bottom; fluid trickling out (about one drip per second) = correct level. Overfilling causes pressure issues.
Measure what drains out and refill the same amount, then verify with the overflow-plug procedure. A simple drain-and-fill typically takes ~5-6 quarts of NS-3 (owners report ~6 quarts in DIY videos); buy six quarts and expect a top-off.
Two filters exist and both are serviceable with the pan down: the pan strainer (Nissan part 31728-1XF03, 3-bolt screen) and the cartridge filter (31726-28X0A) behind a side cover. That said, a NicoClub technical expert (2013 Altima owner) notes CVTs don't load filters with clutch material like conventional automatics, so if fluid is kept fresh the filters rarely need changing — a pan drop around 60k 'won't hurt' if you're ambitious, but most owners just do drain-and-fills.
After the service, a scan tool is used to reset the CVT fluid deterioration data in the TCM so the car tracks fresh fluid life.
Diagnosis starts with a scan for the judder DTCs. The TCM reflash is a dealer visit — no DIY tools needed beyond getting the car there. The valve body lives under the CVT pan: drain the NS-3 fluid, drop the pan, unbolt the valve body. A borescope to inspect the belt/chain while the valve body is out is strongly recommended.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
CVT oil pan bolts: 7.9 N·m (70 in-lb) — From Nissan TSB NTB16-110o covering 2013-2017 Altima JF016E valve-body work (same figure as the existing CVT fluid note); existing bolts are reused.
Valve body bolts: verify — Confirm against Nissan factory service info — torque not verified from the sources reviewed.
Tips
Judder has a Nissan-defined repair path — do not start with a fluid change and hope. TSB NTB16-110 (superseding NTB15-084) covers 2013-2017 4-cylinder Altimas storing judder codes P17F0 or P17F1: TCM reflash first, then mechanical repair only if the judder persists.
The reflash is free at the dealer and is always step one — owners report judder resolved by software alone. Have the dealer check for TCM updates by VIN before spending anything.
P0776 or P1715 (pressure-control solenoid performance) points at the valve body: TSB NTB15-087 covers valve-body replacement with a confirmed DTC. A documented 2014-owner DIY did the full job — drain, drop pan, swap valve body, new strainer and filter, refill with NS-3.
Inspect the belt/chain with a borescope while the valve body is out. The same DIY owner found his belt slipping after the valve-body swap — no valve body saves a worn belt, and the TSB path then ends at torque converter (NTB13-086) or full CVT assembly.
A replacement valve body needs programming/adaptation afterward — dealer-level scan-tool territory. Buy the valve body from Nissan; refurbished units have been reported faulty by owners.
Check warranty coverage before paying out of pocket: Nissan extended CVT coverage on 2013-2016 Altimas under the class-action settlement, and owners in the forums had full transmissions replaced under it.
The electric power-steering pump and its plumbing sit in the engine bay; the noise transmits through brackets and tubing into the cabin. Diagnose by ear with the hood open — have someone turn the wheel while you listen for whether the sound comes from the pump itself or the firewall/fender area.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Tips
Dealers routinely call this whine 'normal' — it is a documented defect. Nissan issued TSB NTB13-017b (Aug 2013) with a VIN-based flowchart and six possible noise paths: a redesigned firewall bracket with rubber isolators for the high-pressure line, hood ledge seal, felt reservoir cover, right-fender noise isolator, lower fender baffle, and a high-pressure line control valve on 4-cylinder cars.
Check the cheap cause first: one owner's dealer found the PS tubing touching metal in the engine bay — bracketing the tubing away from contact killed the whine completely after a pump replacement had failed to help. Look for tubing or brackets contacting the strut tower or firewall before buying any parts.
Do not start with a pump replacement. Multiple owners had the pump swapped with zero change — the noise travels through the mounting bracket, and insulating the bracket fixed cars the pump swap didn't.
Document the noise with the dealer before the warranty expires. Owners who had complaints on record got Nissan USA to cover the roughly $535 in TSB parts after warranty; without a paper trail, dealers fall back to 'normal'.
Use only Nissan EPS fluid if topping up — a Nissan tech specifically warns against substitutes, and the wrong fluid is a known noise contributor.
The crankshaft position sensor sits low on the engine block — access from below with the car safely raised; one 10mm bolt. The camshaft position sensor is up top and easier to reach. Both are basic-hand-tools jobs.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
Typical time: “One 2014 owner's cam-sensor fix lasted 24 hours on an aftermarket part.” — as written in the note. First-timers often take twice this.
Torque specs
Crankshaft position sensor bolt: 5 ft-lb — Per the 2013-2018 replacement walkthrough; confirm against Nissan factory service info.
Camshaft position sensor bolt: verify — Confirm against Nissan factory service info — not verified from the sources reviewed.
Tips
The community-proven rule on these cars: buy OEM Nissan sensors. Aftermarket crank/cam sensors are a documented dead end — owners have had brand-new aftermarket sensors fail immediately or set the same codes, fixed only by the dealer part. One 2014 owner's cam-sensor fix lasted 24 hours on an aftermarket part.
Replace crank and cam sensors as a pair when chasing P0335/P0725. Nissan's own early-2010s TSB guidance says to do both, and owners confirm the second code frequently follows the first — doing one invites a repeat visit.
Check the connector before condemning the sensor: oil can wick through the crank sensor into its electrical connector and keep setting codes after the sensor itself is replaced. Disconnect it, saturate with brake cleaner, dry with compressed air, and confirm the lock fully snaps.
Symptom tell: the RPM needle dropping to zero at idle or during cranking while the engine keeps running points at the crank sensor signal — not fuel delivery or ignition. That specific symptom has been diagnosed to the crank sensor more than once on 2015s.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 553 complaints for the 2013–2018 Nissan Altima. 2016 was the worst year (553 complaints). Most-reported areas: power train, engine, unknown or other.
20V315000 (28/05/2020) — LATCHES/LOCKS/LINKAGES:HOOD:LATCH Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2018 Nissan Altima vehicles. If the primary hood latch is inadvertently released, there is an increased likelihood that the secondary hood latch may corrode over time.
16V244000 (26/04/2016) — AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION Nissan North America, Inc. (Nissan) is recalling certain model year 2016-2017 Nissan Maxima, 2013-2016 Nissan Altima, NV200, LEAF, Sentra, and Pathfinder, 2014-2016 Nissan NV200 Taxi, Infiniti QX60, QX60 Hybrid, and Q50 Hybrid, 2014-2017 Nissan Rogue and Infiniti Q50, 2015-2016 Nissan…
18V915000 (19/12/2018) — STRUCTURE:EMERGENCY:ESCAPE/EGRESS/EXIT Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles, previously remedied under recall number 17V-040. The door latch-lock cable may not have been routed properly in the rear door when the remedy was applied. As a result, the…
17V040000 (18/01/2017) — LATCHES/LOCKS/LINKAGES:DOORS:LATCH Nissan North America, Inc. (Nissan) is recalling certain 2015-2017 Altima vehicles. The rear door latch/lock cable on the vehicles may have been improperly routed. As a result, lowering a rear window may inadvertently cause that door to unlatch and open.
4 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
NHTSA has published 580 manufacturer communications (service bulletins, dealer notices) covering the 2013–2018 Nissan Altima.
Most cited systems: Equipment (182), Electrical System (179), Power Train (114), Engine And Engine Cooling (49), Engine (46).
NHTSA also opened 6 defect investigations covering these years.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.