Diagnose soonLimp mode is protective - diagnose before driving far.
Your transmission needs to know engine RPM to shift, and that signal is faulty. It usually comes from the crankshaft sensor circuit - check that sensor and the wiring between the engine and transmission computers.
Key facts
P0725 means engine Speed Input Circuit. Your transmission needs to know engine RPM to shift, and that signal is faulty. It usually comes from the crankshaft sensor circuit - check that sensor and the wiring between the engine and transmission computers. WrenchFair's published fair-price range for this repair is $40–$200 parts and $100–$300 labor at independent shops.
WrenchFair rates P0725 a 3-of-5 DIY difficulty (“Often shared with an engine crank-sensor code - fix that first.”) with a “Diagnose soon” driveability rating: Limp mode is protective - diagnose before driving far. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 580 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Power Train) — see the latest ones
On your 2013–2018 Nissan Altima (2.5L QR25DE + Jatco CVT8 (JF016E)) — Crank/cam sensor no-start and stalling (P0335/P0725):Owner-verified
The crankshaft position sensor sits low on the engine block — access from below with the car safely raised; one 10mm bolt. The camshaft position sensor is up top and easier to reach. Both are basic-hand-tools jobs.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0725 on the 2013–2018 Nissan Altima — but the community-sourced Crank/cam sensor no-start and stalling (P0335/P0725) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Crankshaft position sensor bolt: 5 ft-lb — Per the 2013-2018 replacement walkthrough; confirm against Nissan factory service info.
Camshaft position sensor bolt: verify — Confirm against Nissan factory service info — not verified from the sources reviewed.
Tips
The community-proven rule on these cars: buy OEM Nissan sensors. Aftermarket crank/cam sensors are a documented dead end — owners have had brand-new aftermarket sensors fail immediately or set the same codes, fixed only by the dealer part. One 2014 owner's cam-sensor fix lasted 24 hours on an aftermarket part.
Replace crank and cam sensors as a pair when chasing P0335/P0725. Nissan's own early-2010s TSB guidance says to do both, and owners confirm the second code frequently follows the first — doing one invites a repeat visit.
Check the connector before condemning the sensor: oil can wick through the crank sensor into its electrical connector and keep setting codes after the sensor itself is replaced. Disconnect it, saturate with brake cleaner, dry with compressed air, and confirm the lock fully snaps.
Symptom tell: the RPM needle dropping to zero at idle or during cranking while the engine keeps running points at the crank sensor signal — not fuel delivery or ignition. That specific symptom has been diagnosed to the crank sensor more than once on 2015s.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
Typical time: “One 2014 owner's cam-sensor fix lasted 24 hours on an aftermarket part.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
limp mode
harsh or no shifts
stalling
check engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
faulty crankshaft position sensor
wiring fault between modules
corroded connector
failed engine computer output (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Check for engine-side crank sensor codes and fix those first.
Test the signal wire between the modules. Tests: wiring fault between modules
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2018 Nissan Altima: Crank/cam sensor no-start and stalling (P0335/P0725) — test first, then buy for this job.
The price range below is a national planning range for P0725 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $200
Labor$100 – $300
Crankshaft position sensor replacement or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0725 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Often shared with an engine crank-sensor code - fix that first.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →