Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA lying range sensor can let the car start in gear - fix soon.
The sensor telling your car which gear you picked (P, R, N, D) is reading wrong - stuck unusually low. That can mean no-start, a lying gear display, or starting in the wrong gear. Check the sensor on the transmission and its connector.
Key facts
P0707 means transmission Range Sensor A Circuit Low. The sensor telling your car which gear you picked (P, R, N, D) is reading wrong - stuck unusually low. That can mean no-start, a lying gear display, or starting in the wrong gear. Check the sensor on the transmission and its connector. WrenchFair's published fair-price range for this repair is $40–$200 parts and $100–$300 labor at independent shops.
WrenchFair rates P0707 a 2-of-5 DIY difficulty (“The sensor is on the transmission; alignment matters.”) with a “Diagnose soon” driveability rating: A lying range sensor can let the car start in gear - fix soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
no-start in park or neutral
wrong gear shown on the dash
backup lights not working
limp mode
Likely causes
failed range sensor
misadjusted range sensor
corroded connector
wiring fault
water in the sensor
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Watch the gear-position reading while moving the shifter.
Check adjustment per the service manual.
Inspect the connector for corrosion. Tests: corroded connector
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $200
Labor$100 – $300
Transmission range sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0707 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The sensor is on the transmission; alignment matters.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →