Your torque converter's lockup clutch is engaging and releasing erratically - expect surging or shuddering at highway speed. Check the lockup solenoid, its wiring, and the fluid.
Key facts
P0744 means torque Converter Clutch Circuit Intermittent. Your torque converter's lockup clutch is engaging and releasing erratically - expect surging or shuddering at highway speed. Check the lockup solenoid, its wiring, and the fluid. WrenchFair's published fair-price range for this repair is $100–$800 parts and $200–$600 labor at independent shops.
WrenchFair rates P0744 a 3-of-5 DIY difficulty (“Solenoid and wiring checks.”) with a “Diagnose soon” driveability rating: Drivable; fix before it strands you. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 580 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Power Train) — see the latest ones
On your 2013–2018 Nissan Altima (2.5L QR25DE + Jatco CVT) — CVT fluid service:Owner-verified
Vehicle-specific service procedure. The L33 Altima CVT (Jatco CVT8 / JF016E) has NO dipstick — the underhood 'cap' is a sealed charge-pipe cap, not a gauge. Fill through the charge pipe/fill plug, then verify level from underneath with the engine running, transmission at ~104°F (40°C), on level ground: remove the overflow plug and a steady trickle (~one drip per second) means the level is correct.
Do this test first: Check the fluid condition.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0744 on the 2013–2018 Nissan Altima — but the community-sourced CVT fluid service note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
CVT oil pan bolts: 7.9 N·m (70 in-lb) — From Nissan TSB NTB16-110o covering 2013-2017 Altima JF016E (RE0F10D) valve-body work; existing bolts are reused.
CVT drain plug: verify — Confirm against Nissan factory service info. Generic Nissan drain-plug guidance cites ~25 ft-lb but is not verified for this aluminum CVT pan.
Overflow/level-check plug: verify — Confirm against Nissan factory service info. 14mm plug reported in owner how-tos; torque value not verified.
Tips
NS-3 ONLY. The 2013 Altima owner's manual (page 385) states: 'Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT, which is not covered by the NISSAN new vehicle limited warranty.' Wrong fluid (e.g. conventional ATF) can require two back-to-back drain-and-fills to correct.
Drain-and-fill beats power-flush in the owner consensus. NicoClub/BITOG owners and a Nissan master tech favor repeated drain-and-fills (roughly every 30k miles) over machine flushes; one Nissan tech warns that servicing a trans whose 30k/60k services were skipped can dislodge deposits and cause problems, and a shop owner quoted on forums says 'DO NOT let anyone flush the transmission. Have the trans pan dropped.' Caveat: one well-regarded NicoClub member disputes the flush-kills myth, noting the pump-driven exchange is gentle and neglected units were likely failing anyway — so treat this as contested, not gospel.
Level check is temperature-critical: no dipstick exists. Nissan tech guidance: warm the CVT to ~104°F (40°C), engine running, car level, pull the overflow plug at the pan bottom; fluid trickling out (about one drip per second) = correct level. Overfilling causes pressure issues.
Measure what drains out and refill the same amount, then verify with the overflow-plug procedure. A simple drain-and-fill typically takes ~5-6 quarts of NS-3 (owners report ~6 quarts in DIY videos); buy six quarts and expect a top-off.
Two filters exist and both are serviceable with the pan down: the pan strainer (Nissan part 31728-1XF03, 3-bolt screen) and the cartridge filter (31726-28X0A) behind a side cover. That said, a NicoClub technical expert (2013 Altima owner) notes CVTs don't load filters with clutch material like conventional automatics, so if fluid is kept fresh the filters rarely need changing — a pan drop around 60k 'won't hurt' if you're ambitious, but most owners just do drain-and-fills.
After the service, a scan tool is used to reset the CVT fluid deterioration data in the TCM so the car tracks fresh fluid life.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
surging at cruise
shuddering
check engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
intermittent TCC solenoid
wiring fault
contaminated fluid
valve body fault
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check the fluid condition.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Test the TCC solenoid and wiring. Tests: intermittent TCC solenoid
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2018 Nissan Altima: CVT fluid service — test first, then buy for this job.
The price range below is a national planning range for P0744 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $800
Labor$200 – $600
TCC solenoid or valve body repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0744 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →