P0744

P0744 on a 2013–2018 Nissan Altima: Torque Converter Clutch Circuit Intermittent

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0744 on a 2013–2018 Nissan Altima

DIY difficulty 3/5

Your torque converter's lockup clutch is engaging and releasing erratically - expect surging or shuddering at highway speed. Check the lockup solenoid, its wiring, and the fluid.

Key facts

☑ Before you buy parts — check these first:
On your 2013–2018 Nissan Altima (2.5L QR25DE + Jatco CVT) — CVT fluid service: Owner-verified
Vehicle-specific service procedure. The L33 Altima CVT (Jatco CVT8 / JF016E) has NO dipstick — the underhood 'cap' is a sealed charge-pipe cap, not a gauge. Fill through the charge pipe/fill plug, then verify level from underneath with the engine running, transmission at ~104°F (40°C), on level ground: remove the overflow plug and a steady trickle (~one drip per second) means the level is correct.
Do this test first: Check the fluid condition.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0744 on the 2013–2018 Nissan Altima — but the community-sourced CVT fluid service note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: 2013 Nissan Altima owner's manual (page 385) — NS-3 fluid spec and warranty warning · NicoClub Altima forum — CVT fluid interval & filter advice (VStar650CL, technical expert) · JustAnswer (ASE/Nissan master tech) — no dipstick; 104°F overflow-plug level check · JustAnswer (Nissan tech) — level check at 110°F, engine running, fill until overflow · JustAnswer (Nissan tech) — internal filter note, flush caution on skipped 30k/60k services · BITOG forum — 2014 Altima drain-and-fills at 143k miles, 30k interval advocacy · YouTube — 2013-2018 Altima CVT transmission filter and fluid change quick guide · YouTube (AhadLivingSpot) — 2013-2018 Altima CVT fluid & filter replacement with OEM part numbers · Nissan TSB NTB16-110o (via Scribd) — JF016E pan bolt torque 7.9 N·m, NS-3 fill, 2013-2017 Altima · NicoClub Altima forum — flush-vs-drain-and-fill debate (myth pushback)

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 3 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check the fluid condition.
  2. Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
  3. Test the TCC solenoid and wiring. Tests: intermittent TCC solenoid

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2013–2018 Nissan Altima: CVT fluid service — test first, then buy for this job.
The price range below is a national planning range for P0744 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$100 – $800
Labor$200 – $600

TCC solenoid or valve body repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0744 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Solenoid and wiring checks.

Watch this repair on YouTube

Parts & tools

Transmission service toolkit — what the job actually takes

Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.

Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →