Diagnose soonNeeds diagnosis - follow the diagnostic path.
Can I drive with P0700?
Can I drive with a P0700 code?
Short trips and gentle driving only, until you know the cause. Needs diagnosis - follow the diagnostic path. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0700?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Needs diagnosis - follow the diagnostic path.
Will P0700 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your transmission's computer found a problem and asked the engine computer to turn on the check engine light. This code alone doesn't say what's wrong - the real answer is in the transmission codes.
Model notes: Cheap code readers often cannot access the transmission module - if you only see P0700 with no detail, the tool is the limitation, not the car.
Key facts
P0700 means transmission control system malfunction (MIL request). Your transmission's computer found a problem and asked the engine computer to turn on the check engine light. This code alone doesn't say what's wrong - the real answer is in the transmission codes. WrenchFair's published fair-price range for this repair is $0–$0 parts and $80–$150 labor at independent shops.
WrenchFair rates P0700 a 2-of-5 DIY difficulty (“The job is reading the TCM codes - a generic reader may not see them; you need a tool that talks to the transmission module.”) with a “Diagnose soon” driveability rating: Needs diagnosis - follow the diagnostic path. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 580 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Power Train) — see the latest ones
On your 2013–2018 Nissan Altima (2.5L QR25DE + Jatco CVT) — CVT fluid service:Owner-verified
Vehicle-specific service procedure. The L33 Altima CVT (Jatco CVT8 / JF016E) has NO dipstick — the underhood 'cap' is a sealed charge-pipe cap, not a gauge. Fill through the charge pipe/fill plug, then verify level from underneath with the engine running, transmission at ~104°F (40°C), on level ground: remove the overflow plug and a steady trickle (~one drip per second) means the level is correct.
Do this test first: Read codes from the transmission control module specifically - not just the engine
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0700 on the 2013–2018 Nissan Altima — but the community-sourced CVT fluid service note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
CVT oil pan bolts: 7.9 N·m (70 in-lb) — From Nissan TSB NTB16-110o covering 2013-2017 Altima JF016E (RE0F10D) valve-body work; existing bolts are reused.
CVT drain plug: verify — Confirm against Nissan factory service info. Generic Nissan drain-plug guidance cites ~25 ft-lb but is not verified for this aluminum CVT pan.
Overflow/level-check plug: verify — Confirm against Nissan factory service info. 14mm plug reported in owner how-tos; torque value not verified.
Tips
NS-3 ONLY. The 2013 Altima owner's manual (page 385) states: 'Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT, which is not covered by the NISSAN new vehicle limited warranty.' Wrong fluid (e.g. conventional ATF) can require two back-to-back drain-and-fills to correct.
Drain-and-fill beats power-flush in the owner consensus. NicoClub/BITOG owners and a Nissan master tech favor repeated drain-and-fills (roughly every 30k miles) over machine flushes; one Nissan tech warns that servicing a trans whose 30k/60k services were skipped can dislodge deposits and cause problems, and a shop owner quoted on forums says 'DO NOT let anyone flush the transmission. Have the trans pan dropped.' Caveat: one well-regarded NicoClub member disputes the flush-kills myth, noting the pump-driven exchange is gentle and neglected units were likely failing anyway — so treat this as contested, not gospel.
Level check is temperature-critical: no dipstick exists. Nissan tech guidance: warm the CVT to ~104°F (40°C), engine running, car level, pull the overflow plug at the pan bottom; fluid trickling out (about one drip per second) = correct level. Overfilling causes pressure issues.
Measure what drains out and refill the same amount, then verify with the overflow-plug procedure. A simple drain-and-fill typically takes ~5-6 quarts of NS-3 (owners report ~6 quarts in DIY videos); buy six quarts and expect a top-off.
Two filters exist and both are serviceable with the pan down: the pan strainer (Nissan part 31728-1XF03, 3-bolt screen) and the cartridge filter (31726-28X0A) behind a side cover. That said, a NicoClub technical expert (2013 Altima owner) notes CVTs don't load filters with clutch material like conventional automatics, so if fluid is kept fresh the filters rarely need changing — a pan drop around 60k 'won't hurt' if you're ambitious, but most owners just do drain-and-fills.
After the service, a scan tool is used to reset the CVT fluid deterioration data in the TCM so the car tracks fresh fluid life.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
transmission symptoms per the underlying fault
possible limp mode
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Any transmission fault stored in the TCM, including sensor or solenoid faults (read TCM codes for the actual fault) 24 owner notes link this repair to P0700
TCM communication issue (rare - usually sets U-codes alongside) 24 owner notes link this repair to P0700
Owner notes linked to P0700: 24 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read codes from the transmission control module specifically - not just the engine Tests: Any transmission fault stored in the TCM, including sensor or solenoid faults (read TCM…
Diagnose the TCM code found there
Check transmission fluid level and condition while you are at it Tests: Any transmission fault stored in the TCM, including sensor or solenoid faults (read TCM…
Clear both modules' codes after repair and road test
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2018 Nissan Altima: CVT fluid service — test first, then buy for this job.
The price range below is a national planning range for P0700 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$0 – $0
Labor$80 – $150
P0700 carries no repair cost of its own — it is a MIL request from the transmission control module. Budget $80-$150 for a transmission diagnosis at an independent shop (dealers charge more); the real code(s) behind it determine the bill. National-average estimate for a diagnostic visit. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0700 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The job is reading the TCM codes - a generic reader may not see them; you need a tool that talks to the transmission module.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →