Diagnose soonWrong pressure - real or reported - can burn clutches fast; do not keep driving hard on this code.
Your transmission's B pressure reading does not add up - either the sensor is lying or the actual fluid pressure is wrong. Either way, shift quality suffers.
Key facts
P0846 means transmission fluid pressure sensor/switch B circuit range/performance. Your transmission's B pressure reading does not add up - either the sensor is lying or the actual fluid pressure is wrong. Either way, shift quality suffers. WrenchFair's published fair-price range for this repair is $80–$400 parts and $200–$500 labor at independent shops.
WrenchFair rates P0846 a 4-of-5 DIY difficulty (“Live-data pressure readings separate sensor faults from real hydraulic problems.”) with a “Diagnose soon” driveability rating: Wrong pressure - real or reported - can burn clutches fast; do not keep driving hard on this code. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 3 factory bulletins on file for this vehicle (mostly Electrical System, Power Train, Unknown Or Other) — see the latest ones
On your 2015–2020 Ford F-150 (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8) — Transmission fluid & filter service:Owner-verified
2015-2016 trucks use the 6R80: pan drop with a replaceable filter, fluid is Motorcraft MERCON LV (XT-10-QLVC, spec WSS-M2C938-A); the 6R80 has a small dipstick/fill tube, and the factory drain-refill procedure adds 3.3L (3.5 qt) initial fill after a pan/filter change with level checked via the level indicator, engine running, after cycling through each gear ~5 seconds. 2017-2020 trucks use the 10R80: there is no conventional dipstick - fill is through a 19mm plug on the side with a short internal level indicator; level is set engine-running in Park at 96-101C (206-215F) and must read between 5 and 6 on the indicator, filled with Motorcraft MERCON ULV (XT-12-QULV, spec WSS-M2C949-A). On the 10R80 you must move heat shields and the auxiliary cooler/lines aside to drop the pan (which has no drain plug); a drain-and-fill exchange of ~5.5 qt is the common DIY middle ground, and a pump/siphon or the cooler-return-line method gets the torque converter fluid the pan drop misses.
Do this test first: Check for TSBs and companion codes; diagnose power faults first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0846 on the 2015–2020 Ford F-150 — but the community-sourced Transmission fluid & filter service note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
10R80 transmission fluid fill plug: 35 lb.ft (47 Nm) — From the Ford factory 10R80 drain-and-refill procedure; do not overfill.
10R80 pan bolts / stud bolts: 10 Nm (bolts); 12 Nm (stud bolts, diagonal pattern) — From Ford Tech Talk June 2020 tech doc on the 10R80 drain and refill procedure.
6R80 pan bolts: verify — Pan bolt torque for the 6R80 not confirmed from a source; confirm against factory service info before torquing. The 6R80 pan gasket is reusable if the rubber regains its shape.
Tips
On the 10R80 the stubby dipstick lives next to the hot exhaust at the side of the case: check level with the engine running at operating temp; expect a toast to the forearm if you aren't careful (owner warning).
10R80 pan has no drain bolt, so siphon fluid out through the fill hole before unbolting the pan to cut the mess.
f150forum consensus: pan drop with filter, then one or two more drain-and-fills within ~10k miles refreshes most of the fluid; thereafter a drain-and-fill every 30k keeps it fresh. The 10R80 pan gasket is reusable (OEM part HL3Z-7A191-B).
Use only the specified fluid per transmission: Mercon LV for the 6R80, Mercon ULV for the 10R80; no additives or flush chemicals per the Ford procedure.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
harsh or slipping shifts
transmission overheating
limp mode
check-engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Real hydraulic pressure problem - low fluid, weak pump, stuck valve (most common) 9 owner notes link this repair to P0846
Failed pressure sensor/switch B reading out of range 9 owner notes link this repair to P0846
Corroded connector skewing the signal
Blocked hydraulic passage or restricted filter 9 owner notes link this repair to P0846
Failed PCM/TCM (rare)
Owner notes linked to P0846: 9 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for TSBs and companion codes; diagnose power faults first.
Check fluid level and condition - low fluid causes real pressure problems that mimic sensor faults. Tests: Real hydraulic pressure problem - low fluid, weak pump, stuck valve (most common)
Watch the B-circuit pressure reading on scan-tool live data during shifts. Tests: Failed pressure sensor/switch B reading out of range
Test line pressure with a manual gauge at the transmission test port if the reading looks wrong. Tests: Failed pressure sensor/switch B reading out of range
Inspect the sensor connector and wiring for corrosion before condemning the sensor.
If pressure is truly wrong, suspect the pump, a stuck valve, or internal leaks - specialist territory.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2015–2020 Ford F-150: Transmission fluid & filter service — test first, then buy for this job.
The price range below is a national planning range for P0846 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$80 – $400
Labor$200 – $500
Transmission fluid pressure sensor/switch replacement or valve-body service. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0846 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Live-data pressure readings separate sensor faults from real hydraulic problems.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →