2015–2020 Ford F-150

Community-sourced DIY repair guides for the 2015–2020 Ford F-150, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.

Owner-verified repair guides

Spark plugs & ignition coils Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

3.5L EcoBoost: done entirely from the top — remove the oil fill cap, pop the engine cover up from the front clips, and all six plugs/coils are exposed; owners call it the easiest plug job they've done. The back two plugs (cylinders 3 and 6, firewall side) are the hardest reach — short mechanics lay a moving blanket across the core support. No intake removal needed on any of the three engines.

Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide · TightTorque — F150 13 (2015–2020) torque table · afcsparkplug — spark plug torque table (OEM/NGK sources) · Lund Racing — Coyote spark plug guide (133 in-lb)

P0300 on this Ford F-150 — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

O2 (oxygen) sensors Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

All four sensors are reached from underneath with the front raised high — upstream pair in the exhaust manifolds/downpipes, downstream pair behind the cats. Seized sensors are the known nightmare: one F150Forum owner needed an oxy/acetylene torch with the bung glowing red-hot to break one free. For stubborn front sensors, pull the passenger front wheel and wheel-well liner to get a breaker-bar angle.

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide

P0131 on this Ford F-150 — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Thermostat replacement Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

3.5L EcoBoost: the thermostat sits on the FRONT of the engine (not up top), behind the turbo charge plumbing. Per the Ford factory procedure you drain the cooling system, remove the air cleaner outlet pipe, and detach the coolant inlet connector — owners report it's 'hard to reach around all the turbo breathing tubes.' The 5.0L V8 is a 10-minute job by comparison: the thermostat housing is exposed up top as soon as the engine cover comes off.

Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide · TightTorque — F150 13 (2015–2020) torque table

P0128 on this Ford F-150 — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Front brake pads & rotors Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

Front brake service on the 13th-gen F-150 is conventional — EPB service mode applies only to the rear brakes. The 2015–2020 front-brake walkthrough lists 13mm and 21mm sockets for the caliper/bracket fasteners, a dual-piston caliper compressor (front calipers are dual-piston), brake cleaner, copper anti-seize, and silicone brake lubricant. Remove the caliper guide-pin bolts to swing the caliper off, then the caliper bracket (anchor plate) bolts to free the rotor. Rotors commonly rust-seize to the hub on these trucks — owners recommend coating the hub mating face with anti-seize so the rotor slides off next time. Light surface rust from sitting a few days usually wears off with driving; persistent pulsation means warped rotors.

Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: f150forum — front rotor replacement tips, anti-seize, bedding · TightTorque — F150 13 (2015–2020) torque table · TRQ/1A Auto — front brakes walkthrough 2015–2020 F-150 (tool list) · AHG — 2015 F-150 caliper/bracket/lug torque confirmation · ford-trucks.com — conflicting 203/55 ft-lbs claim from 2020 factory manual · f150forum — rust buildup after sitting, warped rotors

C0035 on this Ford F-150 — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Battery replacement Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

Battery is in the engine compartment on the 13th-gen F-150, secured by a hold-down (vehicle-specific hold-down parts are listed for the 2015 F-150). Common OE sizes are H6/H7; the tray also accepts an H8 as an upgrade. Trucks with auto start-stop (e.g. 2.7L EcoBoost) use an AGM battery. Ford's BMS battery-monitoring sensor lives on the negative battery cable — the BCM reads state of charge through it. After installing a NEW battery, perform the owner's-manual battery-sensor reset: ignition ON, engine OFF; within 10 seconds, flash the high beams 5 times, then press/release the brake pedal 3 times; the battery/charging-system telltale flashes 3 times within ~15–30 seconds to confirm. Letting the truck sit locked for 8+ hours only relearns the state of charge — it does NOT reset the battery-age parameter, so the manual reset (or FORScan's 'BdyCM Battery Monitoring System Reset' service function under the wrench icon) is required with a new battery.

Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: f150forum — BMS reset after new battery, 8-hour sleep procedure · f150forum — no-scan-tool BMS reset steps, H7 to H8 upgrade · f150forum — AGM battery on 2015 with auto start-stop · YouTube — F-150 battery replacement + BMS reset walkthrough (2015–2022) · escapeforum — workshop-manual rule: manual BMS reset mandatory with new battery · f150forum — FORScan BdyCM Battery Monitoring System Reset path · SHO Forum — Ford BMS negative-cable sensor, charging bypass caution · TightTorque — F150 13 (2015–2020) torque table · Ford workshop manual — Battery, Mounting & Cables (hold-down 7 Nm / 62 lb-in)

P0560 on this Ford F-150 — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Alternator replacement Community-reported (3.5L V6 (EcoBoost))

Alternator sits on the driver's side front of the engine. Disconnect the negative battery terminal first (loosen the 10mm nut, don't fully remove it). Release the serpentine belt tensioner with a 14mm wrench or belt tool — note the belt routing before removal. Remove the protective boot and the 13mm nut on the alternator wiring terminal, then squeeze the locking tab on the small connector and pull it out. Remove the upper 15mm mounting nut (the whole stud may come out with it — inspect it and thread it back in a couple turns to hold position), then the lower 15mm bolt. Gently pry/rock the alternator off its lower mount with a pry bar and rubber mallet, then lift it off the top stud.

Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: TRQ video walkthrough (1A Auto)

P0620 on this Ford F-150 — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Fuel pump replacement Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

The pump is an in-tank module with no service access panel in the bed: you either drop the tank (two straps; support it with a floor jack) or lift/slide the bed back. Drain or siphon the tank as empty as possible first. Per a 2015 F-150 2.7L walkthrough, unbolt the filler neck from the body, lower the tank slightly so the neck drops with it, then loosen the clamp with a ratchet wrench for easy access. The module is held by a plastic lock ring tapped counterclockwise with a brass punch and hammer; the electrical connector has a red slider lock (slide the red tab out, then push down on the tab at the connector end) and the EVAP/fuel lines use squeeze-to-release quick connectors.

Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: TRQ/1A Auto walkthrough: How to Replace Fuel Pump Assembly 2015-2020 Ford F-150 (done on 2015 XLT 3.5L; tools include brass punch, hammer) · 1A Auto fuel pump replacement guide (tank removal, lock-ring hammer method) · JustAnswer: 2015 Ford F-150 2.7L fuel tank removal tips (filler neck, connector red-tab lock) · f150forum: Fuel Pump thread (2016 3.5 EcoBoost failure discussion, pump-only swap tip)

P0087 on this Ford F-150 — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Throttle body cleaning Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

On the 5.0L the throttle body sits front-center on the intake: per the Ford factory procedure (posted on f150forum) you remove the air cleaner outlet pipe, disconnect the electrical connector, and remove the four retaining bolts; the TB gasket is inspected and replaced as needed, not automatically discarded. For cleaning, remove the body from the plenum rather than spraying it in place so cleaner doesn't run into the electronics, and scrub the butterfly edges and bore where carbon rings form. Ford bodies carry a special anti-friction coating, so use a cleaner labeled for throttle bodies, not brake or carb cleaner. On the 2.7L EcoBoost, a dedicated 2015-2020 walkthrough video covers access, removal, and install torque.

Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).

Typical time: “After a cleaning or replacement on a 2015 F-150 3.5L EcoBoost, one documented fix: battery disconnected ~40 minutes, reconnect, start without touching the pedal, let it reach operating temp (~200F), then a test drive;…” — as written in the note. First-timers often take twice this.

Torque specs

Tips

Sources: Ford factory throttle-body R&R procedure, 2019 F-150 5.0L (62 lb.in + 60 deg, gasket inspection), posted on f150forum · YouTube: How to replace the Throttle Body 2015-2020 2.7 Ford F-150 (access, removal, install torque) · JustAnswer: Ford F-150 3.5L EcoBoost P0299 case with throttle-body relearn outcome (battery disconnect 40 min, warm idle, test drive) · f150online forum: Cleaning The Throttle Body (remove from plenum; do not cycle electronic TB disconnected) · aFe instruction manual P/N 46-39113, 2015-2017 F-150 5.0L TB install (factory torque citation)

No owner reports yet — fixed this yourself? tell us how

Transmission fluid & filter service Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

2015-2016 trucks use the 6R80: pan drop with a replaceable filter, fluid is Motorcraft MERCON LV (XT-10-QLVC, spec WSS-M2C938-A); the 6R80 has a small dipstick/fill tube, and the factory drain-refill procedure adds 3.3L (3.5 qt) initial fill after a pan/filter change with level checked via the level indicator, engine running, after cycling through each gear ~5 seconds. 2017-2020 trucks use the 10R80: there is no conventional dipstick - fill is through a 19mm plug on the side with a short internal level indicator; level is set engine-running in Park at 96-101C (206-215F) and must read between 5 and 6 on the indicator, filled with Motorcraft MERCON ULV (XT-12-QULV, spec WSS-M2C949-A). On the 10R80 you must move heat shields and the auxiliary cooler/lines aside to drop the pan (which has no drain plug); a drain-and-fill exchange of ~5.5 qt is the common DIY middle ground, and a pump/siphon or the cooler-return-line method gets the torque converter fluid the pan drop misses.

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: Ford factory 6R80 transmission fluid drain/refill procedure (Mercon LV, 3.3L initial fill, level check), posted on f150forum · Ford factory 6R80 transmission fluid exchange procedure (Mercon LV spec), posted on f150forum · Ford factory 10R80 drain-and-refill procedure (Mercon ULV XT-12-QULV, 96-101C level check between 5 and 6, fill plug 35 lb.ft), posted on lightningerevforum · Ford Tech Talk June 2020: 10R80 drain and refill procedure (10 Nm / 12 Nm pan torque), via mustang6g · YouTube: Ford 10R80 Transmission Complete Fluid & Filter Service (heat-shield/cooler-line access, siphon-first trick) · YouTube: 2017-2023 Ford F150 10R80 fluid change DIY (19mm fill plug, ~5.5 qt per drain & refill, 2019 F-150) · YouTube: 2015-2017 F150 6R80 fluid exchange via cooler return line (Mercon LV) · f150forum: Slightly brown transmission fluid thread (pan-drop strategy, reusable gasket, 30k drain-and-fill cadence)

P0700 on this Ford F-150 — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

IWE 4x4 vacuum grinding noise — check valve and solenoid diagnosis Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

Fully DIY-able diagnosis and repair: the check valve and solenoid are inexpensive parts accessible without dropping the axle, though a half-engaged hub left grinding long enough will damage the IWE actuator and turn a $30 fix into a hub replacement.

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: F150Forum IWE issue thread — owner diagnosis, check-valve/solenoid failure discussion · Ford TSB 20-2028 (IWE noise inspection and repair procedure) full text, mirrored on F150Forum · Owner video: IWE grinding noise explained — vacuum leak, solenoid, check valve causes · Owner video: F-150 IWE check valve grinding fix with part numbers (2017 Raptor)

No owner reports yet — fixed this yourself? tell us how

Blend door actuator clicking / one-side heat — replacement Owner-verified (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

DIY-friendly on the driver's side; the passenger-side actuator is the notorious one — the factory procedure calls for major dash/console removal, but owners documented reaching it through the vent by feel. Budget patience, trim tools, and a headlamp.

Typical difficulty: Easy — based on 16 code guides for the ac repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: F150Forum 2015–2020 blend door actuator master thread — symptoms per side, access tricks · F150Forum 2015+ heater blend door actuator replacement guide with OEM part numbers (PDF) · Owner video: blend door actuator removal without removing the dash

No owner reports yet — fixed this yourself? tell us how

Frozen door latches in cold weather (CSP 18N03 / recall 17S33) Factory-documented (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8)

If your doors already freeze: do NOT force the handles — the cables kink and the latch brackets break, turning a free warranty repair into a parts bill. If a door won't latch shut, hold it closed and drive gently to somewhere warm, or carefully warm the latch area; the mechanism usually releases once thawed. Check whether your VIN is covered before paying anyone: CSP 18N03 covers 2015–2018 F-150s built at Dearborn through 4/12/2018 and Kansas City through 4/3/2018, and coverage transfers to subsequent owners with the program running through 10/31/2028. The dealer repair is free if the truck exhibits the condition: additional sealing on the front and crew-cab rear doors, lubrication of the latch/handle/cable components, cleaning the door drain holes, injecting washer concentrate or methanol into the exterior handle cables, and a wiper clip on the cable ends. While waiting on parts or an appointment, the owner-verified mitigations are keeping the door drain holes clear, a light silicone lubricant on the accessible latch components, and parking nose-out of the wind when a freeze is forecast.

Torque specs

Tips

Sources: Ford Customer Satisfaction Program 18N03 full text: 2015–2018 F-150 door-latch freezing (ford.oemdtc.com) · F150Forum master thread: frozen-latch TSB/recall/CSP history and owner reports, 2015+ · Door-latch freezing class-action settlement: up to $600 out-of-pocket recovery (CarComplaints)

No owner reports yet — fixed this yourself? tell us how

Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

DIY-friendliness scorecard

Score: 97/100 — DIY-friendly

How this is scored (mechanical, no opinion): start at 100; −4 per distinct special tool mentioned in the notes (max −28); −15 per documented dealer-only step (max −30); note-volume band: 15+ notes +10, 8–14 +5, 4–7 +0. Bands: 85+ DIY-friendly · 65–84 DIY with care · 40–64 Experienced DIY only · below 40 Think twice. Pilot rubric — flagged for Robbie’s eyeball before any scale-up.

Codes on this F-150

C0035
2015–2020 Ford F-150
Front brake pads & rotors
C0040
2015–2020 Ford F-150
Front brake pads & rotors
C0041
2015–2020 Ford F-150
Front brake pads & rotors
C0060
2015–2020 Ford F-150
Front brake pads & rotors
P0087
2015–2020 Ford F-150
Fuel pump replacement
P0117
2015–2020 Ford F-150
Thermostat replacement
P0121
2015–2020 Ford F-150
Throttle body cleaning
P0128
2015–2020 Ford F-150
Thermostat replacement
P0130
2015–2020 Ford F-150
O2 (oxygen) sensors
P0131
2015–2020 Ford F-150
O2 (oxygen) sensors
P0151
2015–2020 Ford F-150
O2 (oxygen) sensors
P0217
2015–2020 Ford F-150
Thermostat replacement
P0221
2015–2020 Ford F-150
Throttle body cleaning
P0230
2015–2020 Ford F-150
Fuel pump replacement
P0231
2015–2020 Ford F-150
Fuel pump replacement
P0232
2015–2020 Ford F-150
Fuel pump replacement
P0300
2015–2020 Ford F-150
Spark plugs & ignition coils
P0301
2015–2020 Ford F-150
Spark plugs & ignition coils
P0302
2015–2020 Ford F-150
Spark plugs & ignition coils
P0303
2015–2020 Ford F-150
Spark plugs & ignition coils
P0420
2015–2020 Ford F-150
O2 (oxygen) sensors
P0430
2015–2020 Ford F-150
O2 (oxygen) sensors
P0463
2015–2020 Ford F-150
Fuel pump replacement
P0507
2015–2020 Ford F-150
Throttle body cleaning
P0560
2015–2020 Ford F-150
Battery replacement
P0562
2015–2020 Ford F-150
Battery replacement
P0563
2015–2020 Ford F-150
Battery replacement
P0620
2015–2020 Ford F-150
Alternator replacement
P0625
2015–2020 Ford F-150
Alternator replacement
P0626
2015–2020 Ford F-150
Alternator replacement
P0700
2015–2020 Ford F-150
Transmission fluid & filter service
P0730
2015–2020 Ford F-150
Transmission fluid & filter service
P0741
2015–2020 Ford F-150
Transmission fluid & filter service
P0780
2015–2020 Ford F-150
Transmission fluid & filter service
P0846
2015–2020 Ford F-150
Transmission fluid & filter service

What owners report

NHTSA recorded 120 complaints for the 2015–2020 Ford F-150. 2016 was the worst year (76 complaints). Most-reported areas: power train, engine, electrical system.

Counts are NHTSA complaints filed for these model years, via the NHTSA API. See data for all F-150 years →

Recalls

25 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.

Factory service bulletins

NHTSA has published 3 manufacturer communications (service bulletins, dealer notices) covering the 2015–2020 Ford F-150.

Most cited systems: Electrical System (2), Power Train (1), Unknown Or Other (1), Communication (1).

Latest bulletins:

Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.

Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.