Diagnose soonWrong pressure - real or reported - can burn clutches fast; do not keep driving hard on this code.
Your transmission's B pressure reading does not add up - either the sensor is lying or the actual fluid pressure is wrong. Either way, shift quality suffers.
Key facts
P0846 means transmission fluid pressure sensor/switch B circuit range/performance. Your transmission's B pressure reading does not add up - either the sensor is lying or the actual fluid pressure is wrong. Either way, shift quality suffers. WrenchFair's published fair-price range for this repair is $80–$400 parts and $200–$500 labor at independent shops.
WrenchFair rates P0846 a 4-of-5 DIY difficulty (“Live-data pressure readings separate sensor faults from real hydraulic problems.”) with a “Diagnose soon” driveability rating: Wrong pressure - real or reported - can burn clutches fast; do not keep driving hard on this code. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 258 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
On your 2021–2026 Nissan Rogue (1.5L VC-Turbo (KR15DDT)) — CVT fluid service:Community-reported
The T33 Rogue's Jatco CVT has no dipstick — service is drain-and-fill plus a level check at a side check port. A DIY walkthrough on a 2023 Rogue SL AWD (KR15DDT) drains 3.5–4 quarts per mini-flush and requires TWO mini-flushes to bring the fluid to like-new condition. Fill is done from above with a funnel and a 3/8-inch I.D. clear hose into the fill port. The fluid level is set with a large hex check-port bolt located about 4 inches from the front driver side of the transmission: with the vehicle as level as possible, add fluid 1/4 quart at a time until it slowly trickles out of the check port.
Do this test first: Check for TSBs and companion codes; diagnose power faults first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0846 on the 2021–2026 Nissan Rogue — but the community-sourced CVT fluid service note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Drain plug torque: verify — Confirm against factory service info before torquing.
Check port bolt torque: verify — Confirm against factory service info before torquing.
Tips
Use ONLY Nissan Genuine OEM CVT-3 (NS-3) fluid, part 999MP-NS300P — no universal or aftermarket CVT fluids.
One drain-and-fill replaces only 3.5–4 quarts; perform two mini-flushes (drain, refill, run and cycle through all gears at least 3 times for 1 minute, drain again, refill) to renew the fluid.
Between the two flushes, cycle through every gear position at least 3 times with the parking brake set, then shut off and let it drain ~3.5–4 more quarts.
Set the final level with the vehicle level: add NS-3 1/4 quart at a time until fluid slowly trickles from the check port, then close it.
Nissan factory bulletins state CVT service is intended for qualified technicians, not DIY — a dealer service may be the safer route while under warranty.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Typical time: “One drain-and-fill replaces only 3.5–4 quarts; perform two mini-flushes (drain, refill, run and cycle through all gears at least 3 times for 1 minute, drain again, refill) to renew the fluid.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
harsh or slipping shifts
transmission overheating
limp mode
check-engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Real hydraulic pressure problem - low fluid, weak pump, stuck valve (most common) 9 owner notes link this repair to P0846
Failed pressure sensor/switch B reading out of range 9 owner notes link this repair to P0846
Corroded connector skewing the signal
Blocked hydraulic passage or restricted filter 9 owner notes link this repair to P0846
Failed PCM/TCM (rare)
Owner notes linked to P0846: 9 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for TSBs and companion codes; diagnose power faults first.
Check fluid level and condition - low fluid causes real pressure problems that mimic sensor faults. Tests: Real hydraulic pressure problem - low fluid, weak pump, stuck valve (most common)
Watch the B-circuit pressure reading on scan-tool live data during shifts. Tests: Failed pressure sensor/switch B reading out of range
Test line pressure with a manual gauge at the transmission test port if the reading looks wrong. Tests: Failed pressure sensor/switch B reading out of range
Inspect the sensor connector and wiring for corrosion before condemning the sensor.
If pressure is truly wrong, suspect the pump, a stuck valve, or internal leaks - specialist territory.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2021–2026 Nissan Rogue: CVT fluid service — test first, then buy for this job.
The price range below is a national planning range for P0846 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$80 – $400
Labor$200 – $500
Transmission fluid pressure sensor/switch replacement or valve-body service. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0846 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Live-data pressure readings separate sensor faults from real hydraulic problems.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →