Diagnose soonBoost faults trigger limp mode to protect the engine. Avoid hard acceleration until diagnosed.
Your turbo isn't making any boost at all - it's a mechanical failure, not a sensor glitch. The car will feel like the turbo isn't even there.
Model notes: Never install a replacement turbo without a new oil feed line and verifying oil supply - most repeat turbo failures are oil starvation, not bad luck.
Key facts
P2262 means turbocharger boost pressure not detected - mechanical. Your turbo isn't making any boost at all - it's a mechanical failure, not a sensor glitch. The car will feel like the turbo isn't even there. WrenchFair's published fair-price range for this repair is $60–$400 parts and $100–$400 labor at independent shops.
WrenchFair rates P2262 a 4-of-5 DIY difficulty (“Turbo mechanical diagnosis is straightforward; replacement is involved and demands clean oil supply.”) with a “Diagnose soon” driveability rating: Boost faults trigger limp mode to protect the engine. Avoid hard acceleration until diagnosed. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2013–2024 Ram 2500 (6.7L Cummins I6 diesel) — 6.7L Cummins VGT soot-sticking / P2262 (exhaust brake hangs, no boost):Owner-verified
Driveway diagnosis first: scan the codes, check the actuator harness and connectors for damage, and try the cleaning step before buying a turbo. Pulling the turbo for a full clean is the bigger job — plan a weekend.
Do this test first: Remove the intake pipe and check the turbo shaft for play and seizure - it should spin freely with minimal play
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2262 on the 2013–2024 Ram 2500 — but the community-sourced 6.7L Cummins VGT soot-sticking / P2262 (exhaust brake hangs, no boost) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Turbo / actuator mounting hardware: verify — Replace the actuator O-ring whenever the actuator comes off; heat-cycled hardware is one-time-use in practice.
Tips
The 6.7's variable-geometry turbo lives in a soot bath, and the VGT vanes run at very tight tolerances. When soot builds up, the vanes stick: the exhaust brake hangs engaged (the truck will not build boost until you slow way down), you get little or no boost under load, black smoke on acceleration, and P2262 — turbocharger boost pressure not detected (mechanical).
Clean-before-you-spend: the first owner fix is Mopar 68044565AB turbocharger cleaner, made to dissolve the carbon and soot deposits off the nozzle ring on the hot side of the VGT. Owners clean in place via a drilled cleaning port or pull the turbo and clean it by hand — several report doing it a couple of times before ever disassembling the turbo.
Rule out the electronics first: check the VGT actuator wiring harness and connectors for damage or poor connections, since a wiring fault mimics a stuck turbo. This is a different campaign from the VGT actuator failure note (P00AF/P003A) — that one is a dead actuator; this one is a soot-stuck turbo with a working actuator.
Know the hard-failure tell: inside the turbo a metal guide ring steers the vanes, and if that ring cracks it jams the vanes permanently — no amount of cleaning fixes it, and the hot-side housing or the turbo itself has to be replaced. FCA's TSB 08-272-26 lists P2262-00 among the 6.7L Cummins air-handling codes to work through systematically.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
severe power loss
no turbo sound or whine
excessive black smoke on diesels
check engine light
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Seized turbocharger (most common - check shaft play)
Massive boost leak - blown intercooler hose or pipe
Wastegate stuck fully open
Broken turbo shaft
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Remove the intake pipe and check the turbo shaft for play and seizure - it should spin freely with minimal play Tests: Seized turbocharger (most common - check shaft play)
Pressure-test the entire charge system for massive leaks Tests: Massive boost leak - blown intercooler hose or pipe
Check that the wastegate is not stuck open Tests: Wastegate stuck fully open
If the turbo is seized, find why before replacing: oil starvation from a clogged feed line kills replacement turbos too
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2024 Ram 2500: 6.7L Cummins VGT soot-sticking / P2262 (exhaust brake hangs, no boost) — test first, then buy for this job.
The price range below is a national planning range for P2262 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$60 – $400
Labor$100 – $400
Valve or hose fix is typical; turbo replacement is far more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2262 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Turbo mechanical diagnosis is straightforward; replacement is involved and demands clean oil supply.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →