Community-sourced DIY repair guides for the 2013–2024 Ram 2500, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
DEF system fault / no-restart countdown Owner-verified(6.7L Cummins Turbo Diesel)
Driveway diagnosis with a scan tool or AlfaOBD. Injector cleaning is driveway-level; DEF pump replacement is an intermediate job.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Tips
The failure mode owners dread: a 'Service DEF System — See Dealer' message with a countdown, ending in 'engine will not restart in X miles.' Take it seriously before the last miles.
Owner-confirmed fixes, in order of cheapness: clean crystallized DEF off the dosing injector, reset the DEF fluid level with AlfaOBD and extend the SCR mileage, or replace the DEF pump.
DEF crystallizes when the truck sits or the fluid is old or contaminated — buy from high-turnover pumps, keep the tank reasonably full, and don't store DEF jugs for months.
A 13-year 6.7L Cummins owner review documents a DEF pump failure as one of the few real failures the truck had — the pump is the wear item of the system.
AlfaOBD with an OBDLink adapter is the owner-standard way to read SCR/DEF faults and perform fluid-level resets on these trucks; a generic code reader usually cannot.
Do not just clear the message and keep driving — the countdown continues and the truck will refuse to restart at zero. Diagnose the actual fault first.
Check the recall before you wrench: this is a free dealer replacement. Chrysler recall T51 (NHTSA campaign 17V-562) covers 2013-2017 Ram 2500, 3500, 4500 and 5500 trucks with the 6.7L Cummins - about 444,000 trucks. The Concentric-brand water pumps built without a vent hole can suffer bearing failure and leak coolant onto hot engine parts, which is a fire risk. Call Chrysler customer service at 1-800-853-1403 and ask about recall T51, or run your VIN through the NHTSA recall lookup. If your truck already had the pump replaced under the recall, you are done; if you are outside the recall years and the pump is weeping, it is a straightforward driveway job - drain, belt off, hoses off, unbolt.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
Water pump mounting bolts: verify — Confirm against factory service info. Use a new O-ring/gasket and refill with coolant meeting Cummins spec; bleed the system fully before driving.
Tips
The recall covers 2013-2017 trucks with the 6.7L Cummins, but only the ones fitted with Concentric-brand water pumps WITHOUT a vent hole. Pumps with a vent hole, or pumps from other brands, are not affected - which is why the dealer inspects rather than blanket-replacing every pump.
The tell is coolant loss with no obvious hose leak: look for weeping at the pump body, the sweet smell of coolant after a hot run, and dropping reservoir level. A failing pump bearing can also throw the serpentine belt, so treat any belt squeal plus coolant loss as urgent.
Do not pay for this yourself until you have checked coverage - the recall began February 2018 and the dealer replacement is free. If your VIN shows an open T51, book the dealer visit; it is a same-day job once parts are in.
Shopping a used 2013-2017 Cummins truck? Check that T51 is closed on the VIN before you buy. An open recall means a free dealer visit, but a pump that has been leaking unnoticed is the fire-risk scenario the recall was issued for.
The actuator is a bolt-on part on the side of the Holset VGT turbo - the replacement itself is driveway-level, but a stock-style actuator must be calibrated to the turbo with a scan tool afterward (or buy the no-calibration City Diesel unit). Diagnose before you buy: P00AF almost always means the actuator, but P226B/P226C means the turbo itself has failed and a new actuator will not help.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
VGT actuator mounting fasteners: verify — Confirm against factory service info when replacing the actuator.
Tips
The symptom set is distinctive: sudden loss of boost and power, the exhaust brake stops working, and the check-engine light throws P00AF (turbo boost control module) and/or P003A (boost control position exceeded learning limit). If your exhaust brake died at the same time the power did, suspect the actuator first - they share the same mechanism.
Buy the right part: P00AF is almost always a bad actuator - but if you also have P226B or P226C, that signals a failed turbocharger, and a new actuator will not fix it. Do not spend $500+ on the wrong component.
With the actuator removed, work the sector gear on the turbo by hand: if it moves freely with light finger pressure, the turbo is fine and the actuator alone is the fix. Stiff or gritty vanes mean soot-stuck vanes and the turbo has to come out - no actuator will save it.
The calibration gotcha: a standard replacement actuator (Holset 5579127H, roughly $400-800) must be calibrated to the turbo with a scan tool after install - budget about $200 at a shop if you do not have the tool. The City Diesel billet actuator replaces the electronics and gear housing as a unit and needs NO calibration, which is why it is the owner-favorite DIY path; the 2013-2023 kit also fits 2007.5-2012 trucks.
2019+ trucks: a PCM software update (TSB 18-066-23) addresses false P0299 codes, and there is a separate service procedure for P0299 sensitivity - have the dealer check for the flash before buying parts. And always work the cheap end first: correct OEM air filter for your generation, intact charge-air-cooler hoses, and a clean MAP sensor (soot from the EGR clogs it and fakes boost readings).
Driveway diagnosis first: scan the codes, check the actuator harness and connectors for damage, and try the cleaning step before buying a turbo. Pulling the turbo for a full clean is the bigger job — plan a weekend.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Turbo / actuator mounting hardware: verify — Replace the actuator O-ring whenever the actuator comes off; heat-cycled hardware is one-time-use in practice.
Tips
The 6.7's variable-geometry turbo lives in a soot bath, and the VGT vanes run at very tight tolerances. When soot builds up, the vanes stick: the exhaust brake hangs engaged (the truck will not build boost until you slow way down), you get little or no boost under load, black smoke on acceleration, and P2262 — turbocharger boost pressure not detected (mechanical).
Clean-before-you-spend: the first owner fix is Mopar 68044565AB turbocharger cleaner, made to dissolve the carbon and soot deposits off the nozzle ring on the hot side of the VGT. Owners clean in place via a drilled cleaning port or pull the turbo and clean it by hand — several report doing it a couple of times before ever disassembling the turbo.
Rule out the electronics first: check the VGT actuator wiring harness and connectors for damage or poor connections, since a wiring fault mimics a stuck turbo. This is a different campaign from the VGT actuator failure note (P00AF/P003A) — that one is a dead actuator; this one is a soot-stuck turbo with a working actuator.
Know the hard-failure tell: inside the turbo a metal guide ring steers the vanes, and if that ring cracks it jams the vanes permanently — no amount of cleaning fixes it, and the hot-side housing or the turbo itself has to be replaced. FCA's TSB 08-272-26 lists P2262-00 among the 6.7L Cummins air-handling codes to work through systematically.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 420 complaints for the 2013–2024 Ram 2500. 2016 was the worst year (258 complaints). Most-reported areas: engine, power train, electrical system.
23V799000 (28/11/2023) — STEERING:STEERING CONTROL MODULE Chrysler (FCA US, LLC) is recalling certain 2023 Ram 1500 Classic, Ram 3500 Classic, 3500 Cab Chassis, 2023-2024 Ram 2500, 4500/5500 Cab Chassis, and Ram 3500 vehicles. The steering column control module may cause the high beams to activate when…
23V654000 (28/09/2023) — BACK OVER PREVENTION:DISPLAY FUNCTION Chrysler (FCA US, LLC) is recalling certain 2022-2023 Ram 1500, Ram 3500 Cab Chassis with GVWR less than 10,000 lbs., and 2022-2024 Ram 2500 vehicles. The radio software may prevent the rearview image from displaying. As such, these vehicles fail…
18V486000 (27/07/2018) — STRUCTURE:BODY:TAILGATE Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may…
22V035000 (27/01/2022) — VISIBILITY:WINDSHIELD WIPER/WASHER:LINKAGES Chrysler (FCA US, LLC) is recalling certain 2019-2020 Ram 2500 and Ram 3500 vehicles, Ram 3500 Cab Chassis, 4500 Cab Chassis, 5500 Cab Chassis and 3500 Cab Chassis with a gross vehicle weight rating (GVWR) of less than 10,000 lbs…
19V021000 (25/01/2019) — STEERING:LINKAGES:DRAG:LINK:CONNECTION Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
20V043000 (24/01/2020) — POWER TRAIN:AUTOMATIC TRANSMISSION Chrysler (FCA US LLC) is recalling certain 2019-2020 Ram 2500 and 3500 Pickup vehicles equipped with six-speed automatic (68RFE) transmissions. A build up of pressure and heat inside the transmission may result in a transmission fluid leak from the dipstick…
28 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2013–2024 Ram 2500 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.