P0238: Turbocharger boost pressure sensor A circuit high
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonBoost faults trigger limp mode to protect the engine. Avoid hard acceleration until diagnosed.
The boost sensor is pegged at maximum, so the computer thinks the turbo is overboosting and cuts power hard to protect the engine. The car will feel gutless.
VW/Audi note (VCDS): A mechanical boost gauge tee'd into the system is the truth-teller that separates sensor lies from real overboost.
Model notes: Genuine overboost is dangerous for the engine - if a mechanical gauge confirms real excessive boost, stop driving hard until the wastegate control is fixed.
Key facts
P0238 means turbocharger boost pressure sensor A circuit high. The boost sensor is pegged at maximum, so the computer thinks the turbo is overboosting and cuts power hard to protect the engine. The car will feel gutless. WrenchFair's published fair-price range for this repair is $60–$400 parts and $100–$400 labor at independent shops.
WrenchFair rates P0238 a 2-of-5 DIY difficulty (“High circuit usually means a short - inspect wiring before replacing the sensor.”) with a “Diagnose soon” driveability rating: Boost faults trigger limp mode to protect the engine. Avoid hard acceleration until diagnosed. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
severe power loss
limp mode
check engine light
Likely causes
Signal wire shorted to voltage (most common)
Failed sensor with internal short
Open ground floating the signal high
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Unplug the sensor - if the reading stays pegged high, the harness is shorted to voltage Tests: Signal wire shorted to voltage (most common)
Check the sensor ground carefully - an open ground floats the signal high Tests: Open ground floating the signal high
Verify actual boost with a mechanical gauge to rule out genuine overboost
Replace the sensor only after wiring is proven good
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $400
Labor$100 – $400
Valve or hose fix is typical; turbo replacement is far more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0238 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — High circuit usually means a short - inspect wiring before replacing the sensor.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →