Diagnose soonThe car can die without warning once the battery depletes - get the charging system tested promptly.
Your car's electrical system voltage is too low. Usually a dying alternator or battery - and it can strand you when the battery runs out.
Model notes: Measure voltage at the battery with the engine running (13.8-14.4V) and again at idle with electrical loads on. Voltage-drop test the cables.
Key facts
P0562 means system voltage low. Your car's electrical system voltage is too low. Usually a dying alternator or battery - and it can strand you when the battery runs out. WrenchFair's published fair-price range for this repair is $100–$500 parts and $100–$350 labor at independent shops.
WrenchFair rates P0562 a 2-of-5 DIY difficulty (“Alternator access varies by engine.”) with a “Diagnose soon” driveability rating: The car can die without warning once the battery depletes - get the charging system tested promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 1,210 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
On your 2007–2018 Jeep Wrangler (3.6L Pentastar V6) — Battery replacement:Owner-verified
Battery sits under the hood in a plastic tray with a felt insulating blanket around it. Photograph the cable layout first. Disconnect the NEGATIVE leads from the terminal clamp first (prevents arcing the positive to the body), then unbolt the positive cables and terminal clamp — factory clamps transfer to the new battery, and the locking tabs on the factory cables align with them. Remove the hold-down bracket with a ratchet and long extension (it clamps the battery foot). For working room, unclip the emissions canister in front of the battery and lean the hood back against the windshield instead of using the prop rod. Fitment: direct-replacement Group 34 for 3.8L JKs; the larger H6 (Group 48) spec'd for the 3.6L fits either generation (posts are reversed vs Group 34, but factory cables are long enough). Reinstall in reverse order.
Do this test first: Measure voltage at the battery running (13.8-14.4V) and at idle with loads on
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0562 on the 2007–2018 Jeep Wrangler — but the community-sourced Battery replacement note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Negative battery cable nut: 45 in-lbs (5 N.m) — 2012 JK FSM value (via FSM-derived table).
Battery terminal clamp nuts: verify — Confirm against factory service info for this vehicle.
Hold-down bracket bolt: verify — Snug — the bracket only clamps the battery foot against the tray. Confirm against factory service info for this vehicle.
Tips
Vent tube: the JK has none to route — the battery sits in the open engine bay, not in a sealed compartment. If your replacement battery ships with a vent port and the Optima-style snap-in plug, cap the port per the battery's instructions.
Terminal order matters: negative off first, positive off second; positive on first, negative on last. Reconnecting wakes the modules — expect the infotainment/info screen to reboot; that is normal.
JK TIPM quirk: the Totally Integrated Power Module is voltage-sensitive. If the Jeep acts strange (wipers, windows, locks) after a battery swap, and a replacement TIPM is ever fitted, it needs a key-on-for-12-seconds learn so it can pull VIN/config data from the PCM.
Parasitic-drain diagnostic (if the new battery keeps dying): put a voltmeter in series between the negative terminal and cable, wait 15-30 minutes for all modules to sleep, and read the draw. Note that connecting the meter wakes the modules again, adding ~10 minutes to the sleep cycle. A fuel-pump relay stuck on inside the TIPM is a common JK drain culprit.
AGM upgrade note: many JK owners upgrade to an AGM deep-cycle battery (e.g., Optima Yellow-Top H6) for winch/light-bar duty; flooded batteries die fast under deep cycling.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Typical time: “Parasitic-drain diagnostic (if the new battery keeps dying): put a voltmeter in series between the negative terminal and cable, wait 15-30 minutes for all modules to sleep, and read the draw.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
battery light
dim lights
multiple warning lights
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failing alternator 40 owner notes link this repair to P0562
Weak battery 40 owner notes link this repair to P0562
Corroded positive cable
Slipping/worn serpentine belt
Owner notes linked to P0562: 41 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Measure voltage at the battery running (13.8-14.4V) and at idle with loads on Tests: Weak battery
Voltage-drop test the cables
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2018 Jeep Wrangler: Battery replacement — test first, then buy for this job.
The price range below is a national planning range for P0562 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $500
Labor$100 – $350
Battery is ~$150-250; alternator replacement runs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0562 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →