Community-sourced DIY repair guides for the 2007–2018 Jeep Wrangler, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Spark plugs and ignition coils Owner-verified(3.6L Pentastar V6)
3.6L Pentastar only (2012-2018). Bank 1 (passenger side) plugs are reachable without disassembly: pop off the engine cover, disconnect the negative battery cable (10mm), slide the vacuum lines aside, and remove the coil hold-down screws (10mm) to lift the coils off — a 12-inch extension and 5/8" spark plug socket reaches the plugs. Bank 2 (driver's side) is the notorious part: the composite intake plenum must come off first. Loosen the three long 8mm capture screws on top of the plenum (they stay captive), remove the two plastic plugs and foam near the firewall, disconnect the two front vent lines, three breather hoses and the heater-core hard-line nuts, remove the four T20 Torx lower plenum screws, the heater-line bracket, the intake tube at the throttle body, the MAP sensor harness and the four driver's-side 10mm plenum nuts, then unplug the throttle-body harness and lift the plenum assembly off as a unit. A foam pad under the plenum covers the bank-2 coils. Factory plug is Champion RER8ZWYCB4, gapped to 0.043".
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Torque specs
Spark plugs: 13 ft-lbs — 2012 JK FSM; hand-start to avoid cross-threading. Do not exceed — JL table agrees at 18 N.m.
Upper intake manifold/plenum bolts (M6): 89 in-lbs (10 N.m) — Composite plenum — snug center-out, torque, then repeat the sequence so the outer bolts don't unload the middle. NOT 89 ft-lbs.
Throttle body bolts (M6), if removed: 62 in-lbs (7 N.m) — Use a new gasket if the throttle body comes off.
Negative battery cable nut: 45 in-lbs (5 N.m) — 2012 JK FSM, per the coil-install wrap-up.
Tips
Replace the rubber plenum gaskets (Mopar 05184331AC) while the plenum is off — they harden and crack. Cheap insurance for a job you don't want to redo.
Jeep does NOT recommend anti-seize on spark plug threads (torque spec assumes dry threads); some off-roaders still use it, but the factory spec is dry.
Smear a light film of dielectric grease inside the coil boots before reinstalling so they release next time.
Blow the plug wells out with compressed air before removing plugs so grit can't fall into the cylinders.
Pain point: the plastic oil filter/cooler housing sits directly under the intake manifold and is a notorious leak point — since the plenum is already off, inspect it now (servicing it later requires the same teardown).
Back up the two foam pieces on the plenum; the rear foam hides screws and the piece covering the coils is easy to lose.
Front brake pads and rotors Owner-verified(3.6L Pentastar V6)
Raise the front, remove the wheel. Unbolt the caliper from the back and pull it off the bracket — hang it with wire, never from the brake hose. Compress the piston with a C-clamp before fitting thicker pads. For rotors, remove the two large caliper-bracket-to-knuckle bolts (21mm head) and pull the rotor straight off the hub. JK-specific quirk: JK rotors have NO retaining screws (that's a JL thing). Factory JK rotors are held by push-on retaining CLIPS on the wheel studs — cut/pry them off and discard them; they are one-time assembly aids. Expect rust between rotor and hub; a few taps with a rubber mallet on the rotor hat breaks it free. Slide pins pull out of the bracket for cleaning and re-greasing.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Front caliper bracket-to-knuckle bolts (21mm): 120 ft-lbs — Matches the JK factory torque sheet (163 N.m); confirmed on a JK front brake install.
Caliper slide-pin (caliper-to-bracket) bolts: 26 ft-lbs — Factory caliper mounting bolt value (35 N.m) reused on JK installs; clean pins and re-grease.
Lug nuts: 100 ft-lbs — JK wheel torque confirmed in multiple JK guides.
Rear caliper bracket bolts (for reference): 75 ft-lbs — Rear-only; fronts are 120 ft-lbs. Don't mix them up.
Tips
Factory threads use threadlocker; clean the bracket bolts with brake cleaner and apply fresh threadlocker on reinstall (DIYers commonly use red on the bracket bolts).
Clean old grease off the slide pins, inspect the rubber boots, and re-grease lightly — seized pins are the usual cause of uneven JK pad wear.
The JK has a solid rear rotor and vented front rotor; confirm left/right rotor orientation before mounting.
Minimum pad thickness is 2-3mm per the JK brakes diagnostic guide; squealing means the wear indicators are already talking.
Pump the brake pedal to seat the pads before driving, then bed the pads with several moderate stops.
Battery sits under the hood in a plastic tray with a felt insulating blanket around it. Photograph the cable layout first. Disconnect the NEGATIVE leads from the terminal clamp first (prevents arcing the positive to the body), then unbolt the positive cables and terminal clamp — factory clamps transfer to the new battery, and the locking tabs on the factory cables align with them. Remove the hold-down bracket with a ratchet and long extension (it clamps the battery foot). For working room, unclip the emissions canister in front of the battery and lean the hood back against the windshield instead of using the prop rod. Fitment: direct-replacement Group 34 for 3.8L JKs; the larger H6 (Group 48) spec'd for the 3.6L fits either generation (posts are reversed vs Group 34, but factory cables are long enough). Reinstall in reverse order.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Typical time: “Parasitic-drain diagnostic (if the new battery keeps dying): put a voltmeter in series between the negative terminal and cable, wait 15-30 minutes for all modules to sleep, and read the draw.” — as written in the note. First-timers often take twice this.
Torque specs
Negative battery cable nut: 45 in-lbs (5 N.m) — 2012 JK FSM value (via FSM-derived table).
Battery terminal clamp nuts: verify — Confirm against factory service info for this vehicle.
Hold-down bracket bolt: verify — Snug — the bracket only clamps the battery foot against the tray. Confirm against factory service info for this vehicle.
Tips
Vent tube: the JK has none to route — the battery sits in the open engine bay, not in a sealed compartment. If your replacement battery ships with a vent port and the Optima-style snap-in plug, cap the port per the battery's instructions.
Terminal order matters: negative off first, positive off second; positive on first, negative on last. Reconnecting wakes the modules — expect the infotainment/info screen to reboot; that is normal.
JK TIPM quirk: the Totally Integrated Power Module is voltage-sensitive. If the Jeep acts strange (wipers, windows, locks) after a battery swap, and a replacement TIPM is ever fitted, it needs a key-on-for-12-seconds learn so it can pull VIN/config data from the PCM.
Parasitic-drain diagnostic (if the new battery keeps dying): put a voltmeter in series between the negative terminal and cable, wait 15-30 minutes for all modules to sleep, and read the draw. Note that connecting the meter wakes the modules again, adding ~10 minutes to the sleep cycle. A fuel-pump relay stuck on inside the TIPM is a common JK drain culprit.
AGM upgrade note: many JK owners upgrade to an AGM deep-cycle battery (e.g., Optima Yellow-Top H6) for winch/light-bar duty; flooded batteries die fast under deep cycling.
Death wobble diagnosis and fix Owner-verified(3.6L Pentastar V6)
With the Jeep on the ground (wheels loaded, not on a lift), start at the track bar: have a helper saw the steering wheel 10-to-2 while you watch/feel both track-bar joints and bracket mounts for any slop — the track bar is the culprit the majority of the time. Remove the track bar bolts and inspect the frame-side and axle-side bracket holes for ovalizing (the classic JK root cause: factory 14mm bolt in a ~15-16mm bracket hole with a bushing sleeve sized for 9/16", which wallows out once loose). Next check all four tie-rod ends and drag-link ends by hand for clunks as the steering changes direction, pry-bar test the ball joints under the front axle (moderately worn ball joints often won't show play — don't rule them out on that test alone), and check control-arm bushings for torn rubber or clamp damage. Then verify caster (~4-5+ degrees, checked with an angle finder under the axle C) and get a dynamic tire balance / check for out-of-round tires before chasing alignment-only fixes.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Torque specs
Track bar axle-side bracket bolt (14mm): 125 ft-lb — Famously critical spec; factory 14mm bolt runs in ~15-16mm bracket holes with a 9/16" bushing sleeve, so under-torquing lets it walk and wallow the hole out. Re-torque at ride height, after 50 miles, and at every oil change / after heavy wheeling.
Track bar frame-side bracket nut: 125 ft-lb — Same 125 ft-lb as axle side; inspect the frame-side bracket welds for cracks during severe death wobble.
Lower control arm bolts (axle and frame): 125 ft-lb — Must be torqued at ride height (wheels on the ground) so bushings aren't clamped out of position — torquing on a hoist tears them prematurely.
Upper control arm bolts (axle and frame): 75 ft-lb — Also torqued at ride height; re-torque after 50 miles.
Lower ball joint: 80 ft-lb — Sourced from JK torque table; confirm against factory service info.
Upper ball joint: 75 ft-lb — Sourced from JK torque table; confirm against factory service info.
Tie rod end ball studs: 63 ft-lb — Check for clunk as steering changes direction — loose TREs (especially driver-side adjusting sleeve) feed wobble.
Tie rod end adjusting-sleeve clamp: 45 ft-lb — The driver's-side adjusting sleeve is a common wear/damage point.
Steering stabilizer (frame and tie-rod mounts): 50 ft-lb — Install/refresh only AFTER death wobble is diagnosed and fixed — it masks DW, it never cures it.
Wheel lug nuts: verify — Confirm against factory service info. Check as part of the routine: loose lugs and improperly installed spacers contribute to wobble.
Tips
If the track-bar bracket holes are ovalized/wallowed out, the proper fix is new Grade 8 hardware (many owners upgrade the 14mm factory bolts to 9/16" Grade 8 with a smooth shank, ~0.011" larger OD) and weld thick washers on each side of the bracket (filed to a snug slip fit) or a reinforcement bracket to return the hole to circular — re-torquing alone will not hold.
Torque track-bar and control-arm bolts with the Jeep's full weight on the tires at ride height, then re-torque after 50 miles and at every oil change / after every heavy wheeling trip; bound-up bushings from air-hoist torquing cause handling issues and DW.
Never replace the steering stabilizer as the 'fix' — it only absorbs the side-to-side harmonics while the loose/worn part keeps chewing up bracket holes, welds, and the new damper itself; dealers often sell a damper as the cure, which is why the wobble comes back.
Even one severe DW episode can damage other components; repeated episodes almost guarantee it — ball joints, tie-rod ends, track-bar bushings, bracket holes and welds, the steering sector shaft, and unit bearings can all be battered, so replace everything found damaged at once or the remaining damage will keep feeding the wobble.
Tire issues precipitate DW (bad dynamic balance, separated plies, out-of-round tires, too much pressure, bent wheels) but are not the cause — a dynamic balance check and rotating the best tires to the front still belong in the checklist before aligning.
Lifted Jeeps typically need caster checked/set higher than stock-machine 'green' (~5-6 degrees preferred by Jeep shops on lifted JKs); setting to factory stock numbers on a lifted Jeep can leave the wobble triggers in place.
Pentastar ticking / rocker arm failure Owner-verified(3.6L Pentastar V6)
The tick comes from the top of the engine — valve covers off to reach the rocker arms and lifters. On the 3.6L the intake plenum comes off first, then the valve covers; the cams stay in the heads while you swap rockers and lifters. Book time is around 10 hours for both banks: a long job, but straightforward hand-tool work with no engine pull.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Typical time: “Book time is around 10 hours for both banks: a long job, but straightforward hand-tool work with no engine pull.” — as written in the note. First-timers often take twice this.
Torque specs
Camshaft cap / valve cover fasteners: verify — Torque specs for cam caps and related fasteners not confirmed from a forum source — confirm against factory service info before torquing. Aluminum threads strip easily.
Tips
Diagnose by ear first: a rhythmic tick from the valve cover that persists warm, often followed by misfire codes (P0300–P0306) as it worsens. A mechanic's stethoscope on the valve cover pinpoints the bank.
Replace all 24 rocker arms and 24 lifters on the affected bank at minimum — most owners and techs do both banks while they're in there, since the rest are the same age and the labor dwarfs the parts.
Inspect every cam lobe before reassembly: light wear on the outside of the lobe is ugly but serviceable; if wear has cut into the inside of the lobe, replace that camshaft too or the misfire will return.
There is no revised 'fixed' rocker — the design is unchanged since the 2016 Pentastar upgrade, so don't pay a premium hunting for one. Melling rockers are a commonly used aftermarket option.
Keep up oil changes with the correct weight after the repair — neglected oil is the prime suspect in premature valvetrain wear on these engines.
The manifolds hide under heat shields low on each side of the 3.8L, below the valve covers — the spark plugs are cradled by them. Shields off (10mm bolts, long extension with a U-joint), then the manifold bolts. Soak everything in penetrating fluid and give it time; the bolts thread into aluminum heads, and a snapped bolt turns a Saturday job into a nightmare.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Exhaust manifold bolts: verify — Manifold bolt torque not confirmed from a forum source — confirm against factory service info before torquing. Bolts thread into aluminum heads; overtightening strips them.
Tips
Diagnose by sound: a sharp ticking on cold start that fades as the engine warms is the classic cracked-manifold signature — the crack closes as the metal expands.
Off-road water splash on a hot manifold is the usual killer, but they also crack from plain age and thermal cycling; the 3.8L manifolds are a known weak point.
Replace rather than patch for a permanent fix — ductile-iron or ceramic-coated aftermarket manifolds resist re-cracking better than stock cast iron.
A high-temp metal patch is a legitimate stopgap (one owner reports 50k miles on a patch), but treat it as temporary, not a repair.
If the cracked section includes the catalytic converter, check the federal emissions warranty (8 years / 80,000 miles) — owners have had manifolds replaced free under it.
Use anti-seize on reassembly and always replace the gasket — never reuse the old one.
No disassembly — this note is about living with the 3.8L's appetite. Check the dipstick at every fuel fill-up and carry a quart in the Jeep; many of these engines drink a quart every 1,000 miles, which Chrysler calls within spec.
Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).
Torque specs
Drain plug and filter cap: verify — No torque-critical fasteners beyond the drain plug in the management routine — confirm the plug spec against factory service info.
Tips
The honest truth first: many 2007–2011 3.8Ls left the Mexican assembly plant with piston rings installed upside down, and the oiling passages sludge easily. There is no cheap permanent fix — treat anyone selling one with skepticism.
The proven owner protocol for years of reliable service: check oil at every fill-up, top off with the same spec oil, and never let it run low. Low oil kills these engines; the consumption itself doesn't if you stay on top of it.
Replace the PCV valve first — it's cheap, takes minutes, and a stuck PCV is the only inexpensive thing that sometimes reduces consumption.
Many owners report 10W-30 slows consumption versus 5W-20. That's a mitigation, not a repair — it doesn't fix the rings.
A leakdown test confirms ring trouble if you want proof before deciding whether to live with it or rebuild.
Everything happens in the under-hood fuse box (the TIPM) — no tank drop, no wire cutting. Pop the TIPM cover and locate the M25 (fuel pump) and M37 (run/start) fuse slots; the bypass installs right on top of the existing fuses.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
TIPM / fuse box fasteners: verify — No torque-critical fasteners — fuse-box work only. Confirm against factory service info if the TIPM itself is removed.
Tips
Diagnose first: crank-no-start with no fuel-pump prime hum when you turn the key to ON, or a pump that keeps running with the key off and drains the battery — both point at the TIPM's soldered-in fuel pump relay, which is not separately serviceable.
The proven fix is an external relay bypass (the plug-in system confirmed for 2007–2018 Wranglers): it routes fuel-pump power around the failed internal relay using the M37 run/start signal. Install takes minutes with no wire cutting.
Don't start with an $800–1000+ dealer TIPM replacement — the bypass both diagnoses (if the pump runs with it installed, the relay was the fault) and fixes the problem for a fraction of the cost.
If a dealer already performed the external-relay recall and cut wires under your TIPM, the plug-in bypass won't fit — that vehicle needs the recall relay itself checked instead.
If you build the bypass cable yourself, use 14-gauge wire — thinner wire overheats in the fuse box.
Steering wheel comes off: disconnect the negative battery cable and wait 15 minutes so the airbag-system capacitor discharges before touching any airbag component. T20 driver removes the steering column shroud; three clips on the back of the wheel release the airbag module (rotate the wheel to position each clip over the opening). Disconnect the two airbag connectors, remove the 13mm steering wheel bolt and pull the wheel, then three T20 screws free the clock spring. Transfer the turn signal and wiper stalks (Phillips) to the new unit. Reinstall the wheel with the bolt torqued to 40 ft-lb, pull the yellow lock pin on the new clock spring, reconnect the airbag, and reconnect the battery.
Typical difficulty: Moderate — based on 60 code guides for the steering repair area (an area-level estimate, not this exact job).
Typical time: “Steering wheel comes off: disconnect the negative battery cable and wait 15 minutes so the airbag-system capacitor discharges before touching any airbag component.” — as written in the note. First-timers often take twice this.
Torque specs
Steering wheel bolt: 40 ft-lb — Torque spec from the JK how-to. Snug the three T20 clock spring screws by feel — they thread into plastic and strip easily.
Tips
Diagnose first: an airbag light and warning chime that come and go, often paired with a dead horn, dead cruise control, or dead steering-wheel buttons, is the classic JK clock spring signature — the ribbon cable inside wears through as the wheel turns. B1B02 is the code owners most commonly report.
2007 Wranglers had a factory recall for the clock spring — check your VIN at nhtsa.gov/recalls or with a dealer before buying parts; 2008+ owners are on their own. Dealers charge $550+ for the job while the part runs about $80 online, so this is one of the best savings-per-hour DIY jobs on a JK.
Buy the correct clock spring for your options — units with and without the steering angle sensor are different parts (verify by part number against your old unit). Getting the wrong one means a return trip.
Keep the steering wheel perfectly straight ahead through the whole job and do not spin the new clock spring — pull its yellow locking pin only AFTER the wheel is reinstalled and torqued. A clock spring installed off-center or spun by hand tears on the first full lock.
The 15-minute battery disconnect is not optional — airbag capacitors hold enough charge to deploy the bag after the cable is off. Never probe an airbag connector with a meter.
If the airbag light is still on after the repair, the fault (usually B1B02) needs to be read and cleared with a scan tool — the clock spring replacement fixes the cause but doesn't always clear the stored code by itself.
Cabin water leaks (wet floorboards after rain) Owner-verified(3.8L V6, 3.6L Pentastar V6)
No disassembly for diagnosis — this note is leak-hunting plus targeted sealing. Park it dry and hose-test one area at a time (doors, freedom panels, cowl) while a helper watches inside. Common entries owners report: door seals (especially the top of the door), freedom-panel seals, clogged cowl drains, the rear fender holes (water travels forward and ponds on the front carpet), and body plugs under the dash. Check the jack/lug-wrench cubby in the rear — owners find standing water there before they notice the front carpet is wet.
Torque specs
Door/hardtop/freedom-panel hardware: verify — No torque-critical fasteners in leak-chasing — snug weatherstrip and hardtop hardware by feel. Overtightening distorts panels and makes leaks worse.
Tips
Understand the root cause before buying anything: unlike most vehicles, the JK has no true body-side gasket seal — the door seals press against painted metal instead of a consistent rubber surface, which is why replacing factory seals alone rarely fixes anything. The durable fix is adding the missing body-side sealing surface (owners use foam-tape body-side gasket kits).
Cheapest proven DIY fixes from owners: reposition the doors so they sit tighter against the seals, slide flexible tubing inside the door seal to stiffen it, add supplemental weatherstripping at the leak point, and silicone-seal the small gaps — one owner drove leak-free for years after the tubing trick.
Clear the cowl drains and check the AC condensate drain before chasing seals — clogged drains back water into the cabin and mimic a door-seal leak exactly. Pull the floor drain plugs and verify they're not the source.
Freedom panels are a separate leak path from the doors: reseat them carefully (dirt in the seals is enough to start a drip) and confirm the rear seal isn't folded. Water from the top of the windshield frame runs down the A-pillar and shows up on the floor mats far from where it entered.
If the carpet has been wet more than once, pull it and dry the tub — owners who skipped this ended up with mold and corrosion under the carpet long after the leak was fixed.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
DIY-friendliness scorecard
Score: 93/100 — DIY-friendly
Special tools mentioned in the notes (3, −12): Torx bits, spark plug socket, scan tool with live data.
Documented dealer-only steps (0, −0): none documented in the notes — that does not mean none exist.
How this is scored (mechanical, no opinion): start at 100; −4 per distinct special tool mentioned in the notes (max −28); −15 per documented dealer-only step (max −30); note-volume band: 15+ notes +10, 8–14 +5, 4–7 +0. Bands: 85+ DIY-friendly · 65–84 DIY with care · 40–64 Experienced DIY only · below 40 Think twice. Pilot rubric — flagged for Robbie’s eyeball before any scale-up.
NHTSA recorded 2,548 complaints for the 2007–2018 Jeep Wrangler. 2008 was the worst year (1255 complaints). Most-reported areas: air bags, power train, electrical system.
19V680000 (26/09/2019) — SEAT BELTS:FRONT:ANCHORAGE Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.
13E010000 (25/02/2013) — EQUIPMENT Quadratec, Inc. is recalling certain aftermarket accessory, driver-side, Ultimate Floor Liners part numbers 14254.0301 07, 14254.0301 08, 14254.0301Q, 14254.0302 07, 14254.0302 08, 14254.0302Q, 14254.0303 07, 14254.0303 08, 14254.0303Q, 14254.0309 07, 14254.0309 08, and 14254.0309Q sold from May 1, 2012, through…
16V352000 (24/05/2016) — AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM…
19V018000 (15/01/2019) — AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure…
24V196000 (14/03/2024) — AIR BAGS:FRONTAL:DRIVER CLOCKSPRING/SPIRAL CASSETTE Chrysler (FCA US, LLC) (Stellantis) is recalling certain right hand drive 2016 Jeep Wrangler vehicles. Debris contamination may cause the clockspring to fail, preventing the driver's air bag from deploying in a crash.
16V734000 (13/10/2016) — AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE Chrysler (FCA US LLC) is recalling certain model year 2016-2017 Jeep Wrangler vehicles manufactured June 16, 2015, to August 14, 2016. In certain crash conditions, the front impact sensor wiring may be pulled until it detaches before a signal can…
17 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
NHTSA has published 1,210 manufacturer communications (service bulletins, dealer notices) covering the 2007–2018 Jeep Wrangler.
Most cited systems: Electrical System (341), Equipment (269), Power Train (173), Structure (147), Engine And Engine Cooling (115).
Latest bulletins:
9100900 (Sep 2026) — Electrical System, Structure
9100363 Rev 3 (Aug 2026) — Engine
114044 (Aug 2026) — Structure
NHTSA also opened 16 defect investigations covering these years.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.