Diagnose soonStalling in traffic is dangerous - diagnose promptly.
The circuit controlling your fuel pump has an electrical fault - stuck unusually low, suggesting a short to ground. Fuel problems cause stalling or no-starts, so check the pump relay, fuse, wiring, and the pump itself.
Key facts
P0628 means fuel Pump A Control Circuit Low. The circuit controlling your fuel pump has an electrical fault - stuck unusually low, suggesting a short to ground. Fuel problems cause stalling or no-starts, so check the pump relay, fuse, wiring, and the pump itself. WrenchFair's published fair-price range for this repair is $80–$600 parts and $150–$450 labor at independent shops.
WrenchFair rates P0628 a 3-of-5 DIY difficulty (“Fuel pressure testing; the pump is in the tank.”) with a “Diagnose soon” driveability rating: Stalling in traffic is dangerous - diagnose promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 1,210 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
On your 2007–2018 Jeep Wrangler (3.8L V6, 3.6L Pentastar V6) — TIPM fuel pump relay failure (crank-no-start):Owner-verified
Everything happens in the under-hood fuse box (the TIPM) — no tank drop, no wire cutting. Pop the TIPM cover and locate the M25 (fuel pump) and M37 (run/start) fuse slots; the bypass installs right on top of the existing fuses.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0628 on the 2007–2018 Jeep Wrangler — but the community-sourced TIPM fuel pump relay failure (crank-no-start) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
TIPM / fuse box fasteners: verify — No torque-critical fasteners — fuse-box work only. Confirm against factory service info if the TIPM itself is removed.
Tips
Diagnose first: crank-no-start with no fuel-pump prime hum when you turn the key to ON, or a pump that keeps running with the key off and drains the battery — both point at the TIPM's soldered-in fuel pump relay, which is not separately serviceable.
The proven fix is an external relay bypass (the plug-in system confirmed for 2007–2018 Wranglers): it routes fuel-pump power around the failed internal relay using the M37 run/start signal. Install takes minutes with no wire cutting.
Don't start with an $800–1000+ dealer TIPM replacement — the bypass both diagnoses (if the pump runs with it installed, the relay was the fault) and fixes the problem for a fraction of the cost.
If a dealer already performed the external-relay recall and cut wires under your TIPM, the plug-in bypass won't fit — that vehicle needs the recall relay itself checked instead.
If you build the bypass cable yourself, use 14-gauge wire — thinner wire overheats in the fuse box.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
hard starting
engine stalling
no-start
loss of power under load
check engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
failed fuel pump
failed fuel pump relay
blown fuse
open or shorted wiring
failed fuel pump control module
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Check the related fuses and relays before condemning any part - an open fuse is a cheap fix.
Check fuel pressure with a gauge - low pressure confirms a delivery problem.
Test the fuel pump relay and wiring. Tests: failed fuel pump relay
Check power and ground at the pump.
Do not run the pump dry.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2018 Jeep Wrangler: TIPM fuel pump relay failure (crank-no-start) — test first, then buy for this job.
The price range below is a national planning range for P0628 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$80 – $600
Labor$150 – $450
Fuel pump replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0628 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Fuel pressure testing; the pump is in the tank.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →