P0628

P0628 on a 2007–2018 Jeep Wrangler: Fuel Pump A Control Circuit Low

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0628 on a 2007–2018 Jeep Wrangler

DIY difficulty 3/5

The circuit controlling your fuel pump has an electrical fault - stuck unusually low, suggesting a short to ground. Fuel problems cause stalling or no-starts, so check the pump relay, fuse, wiring, and the pump itself.

Key facts

☑ Before you buy parts — check these first:
On your 2007–2018 Jeep Wrangler (3.8L V6, 3.6L Pentastar V6) — TIPM fuel pump relay failure (crank-no-start): Owner-verified
Everything happens in the under-hood fuse box (the TIPM) — no tank drop, no wire cutting. Pop the TIPM cover and locate the M25 (fuel pump) and M37 (run/start) fuse slots; the bypass installs right on top of the existing fuses.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0628 on the 2007–2018 Jeep Wrangler — but the community-sourced TIPM fuel pump relay failure (crank-no-start) note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: manufacturer · owner review · owner forum · TSB document

Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
  2. Check the related fuses and relays before condemning any part - an open fuse is a cheap fix.
  3. Check fuel pressure with a gauge - low pressure confirms a delivery problem.
  4. Test the fuel pump relay and wiring. Tests: failed fuel pump relay
  5. Check power and ground at the pump.
  6. Do not run the pump dry.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2007–2018 Jeep Wrangler: TIPM fuel pump relay failure (crank-no-start) — test first, then buy for this job.
The price range below is a national planning range for P0628 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$80 – $600
Labor$150 – $450

Fuel pump replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0628 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Fuel pressure testing; the pump is in the tank.

Watch this repair on YouTube

Parts & tools

Fuel system toolkit — what the job actually takes

Torque specs: Fuel rail bolts: typically 8–12 Nm — verify spec.

Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →