Diagnose soonThe car can die without warning once the battery depletes - get the charging system tested promptly.
Your car's electrical system voltage is too low. Usually a dying alternator or battery - and it can strand you when the battery runs out.
Model notes: Measure voltage at the battery with the engine running (13.8-14.4V) and again at idle with electrical loads on. Voltage-drop test the cables.
Key facts
P0562 means system voltage low. Your car's electrical system voltage is too low. Usually a dying alternator or battery - and it can strand you when the battery runs out. WrenchFair's published fair-price range for this repair is $100–$500 parts and $100–$350 labor at independent shops.
WrenchFair rates P0562 a 2-of-5 DIY difficulty (“Alternator access varies by engine.”) with a “Diagnose soon” driveability rating: The car can die without warning once the battery depletes - get the charging system tested promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2020–2021 Ford Explorer Hybrid (3.3L V6 hybrid (FHEV)) — No-start with 'Stop Safely Now' — check 12V first (SSM 50151):Factory-documented
The owner-side takeaway is a 12V health check, not module replacement. If the hybrid throws hybrid-system codes at key-on, test or charge the 12V auxiliary battery first and clear low-voltage codes before authorizing any SOBDMC/SOBDMB module work.
Do this test first: Measure voltage at the battery running (13.8-14.4V) and at idle with loads on
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0562 on the 2020–2021 Ford Explorer Hybrid — but the community-sourced No-start with 'Stop Safely Now' — check 12V first (SSM 50151) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
12V battery terminals: verify — Snug and clean — no published torque figure in the SSM. Confirm against factory service info.
Tips
On 2020-2021 Explorer Hybrids, a no-start with a 'Stop Safely Now' message in the cluster is frequently a 12V problem wearing a hybrid-system disguise. Ford SSM 50151 says the SOBDMC/SOBDMB modules will set codes P0A23, P0A6F, P0A72, P0A75, P0A71, P0A74, P0A77, P0DFA, P06B1, P0A47, or P1A0E — often right at key-on and hard to reproduce.
Ford's prescribed order: before replacing either secondary on-board diagnostic module, diagnose any low-voltage DTCs (P0562, U3003) in the other modules first. If the snapshot data shows less than 10 volts, the 12V system is the problem — fix that per the workshop manual (section 418-00) and recheck.
Practical version: a weak or aging 12V auxiliary battery is the first suspect, not the hybrid hardware. Load-test the 12V, check for parasitic draw if it keeps going flat, and only then consider module replacement.
This is the same 12V-first logic behind the deep-sleep complaints on these trucks (FordPass 'deep sleep' warnings, dead fob, disabled auto start-stop) — the hybrid will not wake its high-voltage system on a sick 12V. SSM 50975 covers the deep-sleep notification behavior across 2017-2022 Ford/Lincoln vehicles.
No hybrid-battery work is involved in this diagnosis — do not let a shop sell a traction-battery repair for a 12V-caused no-start.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
battery light
dim lights
multiple warning lights
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failing alternator 40 owner notes link this repair to P0562
Weak battery 40 owner notes link this repair to P0562
Corroded positive cable
Slipping/worn serpentine belt
Owner notes linked to P0562: 41 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Measure voltage at the battery running (13.8-14.4V) and at idle with loads on Tests: Weak battery
Voltage-drop test the cables
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2020–2021 Ford Explorer Hybrid: No-start with 'Stop Safely Now' — check 12V first (SSM 50151) — test first, then buy for this job.
The price range below is a national planning range for P0562 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $500
Labor$100 – $350
Battery is ~$150-250; alternator replacement runs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0562 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →