Diagnose soonMisfires can damage the catalytic converter. Drive gently to a shop; if the check-engine light is flashing, stop driving.
The sensor monitoring the exhaust camshaft has an electrical fault. On high-mileage engines this can also be a sign the timing chain has stretched.
Model notes: Sensor B (exhaust cam) codes on high-mileage engines deserve a timing chain stretch check - the sensor is often reporting correctly that the cam is not where the ECM expects it.
Key facts
P0365 means camshaft position sensor B circuit malfunction, bank 1. The sensor monitoring the exhaust camshaft has an electrical fault. On high-mileage engines this can also be a sign the timing chain has stretched. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$180 labor at independent shops.
WrenchFair rates P0365 a 2-of-5 DIY difficulty (“Exhaust cam sensors are usually as accessible as intake ones; verify timing components if the sensor tests good.”) with a “Diagnose soon” driveability rating: Misfires can damage the catalytic converter. Drive gently to a shop; if the check-engine light is flashing, stop driving. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2016–2016 Dodge Journey (2.4L Tigershark I4) — Intermittent stall / no-start — crank & cam sensor connector recall S89:Factory-documented
Dealer-only repair — a connector and terminal replacement, not a sensor swap you can do in the driveway. If your 2016 Journey stalls intermittently, check this recall by VIN before replacing sensors.
Do this test first: Test the sensor and its wiring the same as any cam sensor
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0365 on the 2016–2016 Dodge Journey — but the community-sourced Intermittent stall / no-start — crank & cam sensor connector recall S89 note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Sensor/connector fasteners: verify — No owner-serviceable torque values for the dealer connector replacement; confirm against factory service info.
Tips
The root cause is NOT bad sensors — it is improperly manufactured crankshaft and/or camshaft sensor electrical connector terminals that make only an intermittent connection. That is why replacing the sensors yourself does not fix it; the fix is the connector and terminals.
Symptoms: engine stalls without warning while driving, engine 'no start' condition, and/or the malfunction indicator lamp. On a 2016 Journey built May 9–July 15, 2016, suspect this before paying for parts.
Documented free route: dealers replace the crankshaft and/or camshaft electrical connector and terminals free of charge (FCA campaign S89, NHTSA 16V-907, ~42,231 vehicles, recall began February 8, 2017).
Confirm coverage with FCA customer service at 1-800-853-1403; this is an intermittent electrical fault, so it may stall only occasionally before it gets worse.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
rough idle
reduced power
poor fuel economy
possible VVT codes alongside
hard starting or no-start
misfiring
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed exhaust cam sensor (most common)
Damaged wiring or oil-fouled connector
Timing component wear causing the signal to drift out of expected range
Low oil pressure affecting the exhaust cam phaser
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Test the sensor and its wiring the same as any cam sensor
If the sensor is good, check camshaft correlation PIDs - a stretched timing chain shows up as cam/crank misalignment
Verify oil level and pressure - phaser faults can set sensor circuit codes Tests: Low oil pressure affecting the exhaust cam phaser
Do not ignore timing chain wear on high-mileage engines with cam codes Tests: Timing component wear causing the signal to drift out of expected range
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2016–2016 Dodge Journey: Intermittent stall / no-start — crank & cam sensor connector recall S89 — test first, then buy for this job.
The price range below is a national planning range for P0365 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $120
Labor$80 – $180
Camshaft/crankshaft position sensor or wiring repair is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0365 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Exhaust cam sensors are usually as accessible as intake ones; verify timing components if the sensor tests good.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →