P0365

P0365 on a 2016–2016 Dodge Journey: Camshaft position sensor B circuit malfunction, bank 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0365 on a 2016–2016 Dodge Journey

DIY difficulty 2/5

The sensor monitoring the exhaust camshaft has an electrical fault. On high-mileage engines this can also be a sign the timing chain has stretched.

Model notes: Sensor B (exhaust cam) codes on high-mileage engines deserve a timing chain stretch check - the sensor is often reporting correctly that the cam is not where the ECM expects it.

Key facts

☑ Before you buy parts — check these first:
On your 2016–2016 Dodge Journey (2.4L Tigershark I4) — Intermittent stall / no-start — crank & cam sensor connector recall S89: Factory-documented
Dealer-only repair — a connector and terminal replacement, not a sensor swap you can do in the driveway. If your 2016 Journey stalls intermittently, check this recall by VIN before replacing sensors.
Do this test first: Test the sensor and its wiring the same as any cam sensor
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0365 on the 2016–2016 Dodge Journey — but the community-sourced Intermittent stall / no-start — crank & cam sensor connector recall S89 note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: recall record (Justia) · recall record

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Test the sensor and its wiring the same as any cam sensor
  2. If the sensor is good, check camshaft correlation PIDs - a stretched timing chain shows up as cam/crank misalignment
  3. Verify oil level and pressure - phaser faults can set sensor circuit codes Tests: Low oil pressure affecting the exhaust cam phaser
  4. Do not ignore timing chain wear on high-mileage engines with cam codes Tests: Timing component wear causing the signal to drift out of expected range

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2016–2016 Dodge Journey: Intermittent stall / no-start — crank & cam sensor connector recall S89 — test first, then buy for this job.
The price range below is a national planning range for P0365 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$30 – $120
Labor$80 – $180

Camshaft/crankshaft position sensor or wiring repair is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0365 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Exhaust cam sensors are usually as accessible as intake ones; verify timing components if the sensor tests good.

Watch this repair on YouTube

Parts & tools

Spark plug & coil toolkit — what the job actually takes

Torque specs: Gasket-seat plugs: typically 20–30 Nm (15–22 lb-ft). Tapered-seat plugs: typically 11–18 Nm. Always verify against your engine’s factory spec — over-torquing strips aluminum threads.

Pro tip: Blow out the plug wells with compressed air BEFORE removing the plugs, so debris can’t fall into the cylinders.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →