Diagnose soonIf the check engine light is flashing, stop driving - raw fuel is cooking the catalytic converter.
The ignition coil for cylinder 6 has an electrical fault.
Key facts
P0356 means ignition coil 'F' primary/secondary circuit. The ignition coil for cylinder 6 has an electrical fault. WrenchFair's published fair-price range for this repair is $40–$150 parts and $50–$150 labor at independent shops.
WrenchFair rates P0356 a 2-of-5 DIY difficulty (“Swap the coil with another cylinder.”) with a “Diagnose soon” driveability rating: If the check engine light is flashing, stop driving - raw fuel is cooking the catalytic converter. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 1,210 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
On your 2007–2018 Jeep Wrangler (3.6L Pentastar V6) — Spark plugs and ignition coils:Owner-verified
3.6L Pentastar only (2012-2018). Bank 1 (passenger side) plugs are reachable without disassembly: pop off the engine cover, disconnect the negative battery cable (10mm), slide the vacuum lines aside, and remove the coil hold-down screws (10mm) to lift the coils off — a 12-inch extension and 5/8" spark plug socket reaches the plugs. Bank 2 (driver's side) is the notorious part: the composite intake plenum must come off first. Loosen the three long 8mm capture screws on top of the plenum (they stay captive), remove the two plastic plugs and foam near the firewall, disconnect the two front vent lines, three breather hoses and the heater-core hard-line nuts, remove the four T20 Torx lower plenum screws, the heater-line bracket, the intake tube at the throttle body, the MAP sensor harness and the four driver's-side 10mm plenum nuts, then unplug the throttle-body harness and lift the plenum assembly off as a unit. A foam pad under the plenum covers the bank-2 coils. Factory plug is Champion RER8ZWYCB4, gapped to 0.043".
Do this test first: Swap coil F with another cylinder's coil
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0356 on the 2007–2018 Jeep Wrangler — but the community-sourced Spark plugs and ignition coils note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Spark plugs: 13 ft-lbs — 2012 JK FSM; hand-start to avoid cross-threading. Do not exceed — JL table agrees at 18 N.m.
Upper intake manifold/plenum bolts (M6): 89 in-lbs (10 N.m) — Composite plenum — snug center-out, torque, then repeat the sequence so the outer bolts don't unload the middle. NOT 89 ft-lbs.
Throttle body bolts (M6), if removed: 62 in-lbs (7 N.m) — Use a new gasket if the throttle body comes off.
Negative battery cable nut: 45 in-lbs (5 N.m) — 2012 JK FSM, per the coil-install wrap-up.
Tips
Replace the rubber plenum gaskets (Mopar 05184331AC) while the plenum is off — they harden and crack. Cheap insurance for a job you don't want to redo.
Jeep does NOT recommend anti-seize on spark plug threads (torque spec assumes dry threads); some off-roaders still use it, but the factory spec is dry.
Smear a light film of dielectric grease inside the coil boots before reinstalling so they release next time.
Blow the plug wells out with compressed air before removing plugs so grit can't fall into the cylinders.
Pain point: the plastic oil filter/cooler housing sits directly under the intake manifold and is a notorious leak point — since the plenum is already off, inspect it now (servicing it later requires the same teardown).
Back up the two foam pieces on the plenum; the rear foam hides screws and the piece covering the coils is easy to lose.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light (may flash)
misfire on cylinder 6
rough idle
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed ignition coil F (most common) 3 owner notes link this repair to P0356
Damaged wiring or corroded connector
Failed coil driver in the ECM
Owner notes linked to P0356: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Swap coil F with another cylinder's coil
Check the coil connector Tests: Damaged wiring or corroded connector
Test coil power and ground
Replace the coil if the fault follows it
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2018 Jeep Wrangler: Spark plugs and ignition coils — test first, then buy for this job.
Expensive fork: Fuel injector, then compression test — if the misfire stays on the same cylinder after a fresh plug and a swapped coil.
The price range below is a national planning range for P0356 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $150
Labor$50 – $150
Ignition coil replacement (coil F). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0356 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →