Diagnose soonDrivable, but boost control and fueling suffer - diagnose soon.
The sensor measuring intake manifold pressure is giving implausible readings. Usually a cheap, easy sensor swap.
Model notes: Quick sanity check: with key on and engine off, the MAP reading should nearly match barometric pressure. Also inspect the sensor port for carbon/oil blockage.
Key facts
P0106 means manifold absolute pressure sensor circuit range/performance. The sensor measuring intake manifold pressure is giving implausible readings. Usually a cheap, easy sensor swap. WrenchFair's published fair-price range for this repair is $30–$120 parts and $50–$150 labor at independent shops.
WrenchFair rates P0106 a 1-of-5 DIY difficulty (“Usually one bolt and a connector.”) with a “Diagnose soon” driveability rating: Drivable, but boost control and fueling suffer - diagnose soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2017–2024 Chevrolet 2500 (6.6L L5P Duramax V8 diesel) — L5P MAP sensor soot caking ('Service Emissions System' countdown):Owner-verified
Driveway fix — the MAP sensor sits on top of the intake near the firewall, held by a single small bolt and one electrical connector. Five-minute removal once you know where it is.
Do this test first: Compare MAP reading to barometric pressure with key on, engine off - they should nearly match
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0106 on the 2017–2024 Chevrolet 2500 — but the community-sourced L5P MAP sensor soot caking ('Service Emissions System' countdown) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
MAP sensor bolt: verify — Single small bolt into the intake — snug only; over-torquing cracks the plastic sensor body. Confirm the spec against factory service info rather than guessing.
Tips
The L5P's EGR system cakes the MAP sensor in soot — owners on the Diesel Page report pulling the sensor to find the tip buried. The giveaway is a 'Service Emissions System' message with a speed-limit countdown (one owner got it at just 8,000 miles) and sometimes a P0106.
The fix owners swear by: pull the sensor (one 10mm bolt on top of the intake near the firewall), spray the soot off with electronics cleaner, and drop it back in. Never use brake cleaner — it attacks the sensor's plastics and potting compounds. The video owner's light and countdown cleared immediately after the cleaning.
If you are cleaning it every few months, the forum's administrator wisdom is that frequent re-sooting points at the EGR system (worse with tunes/power-adders), not the sensor. A spacer that moves the sensor tip out of the soot stream extends the cleaning interval — but it is a band-aid over an EGR that is loading up the DPF.
Cleaning technique matters: do not poke the sensing element with anything harder than an acid brush. A drop or two of kerosene or diesel fuel on the brush breaks up caked soot, followed by electronics cleaner or rubbing alcohol to dry it out. Owners with chronic sooters keep a spare cleaned sensor on the shelf to minimize downtime.
Do not throw an aftermarket sensor at a sooty intake first — owners report the OEM sensor plus a cleaning fixes it. A new sensor in a sooty intake just starts caking from mile one.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
boost issues
rough running
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed MAP sensor
Blocked sensor port (carbon/oil sludge)
Wiring fault
Actual mechanical issue (jumped timing gives odd manifold pressure)
Owner notes linked to P0106: 3 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Compare MAP reading to barometric pressure with key on, engine off - they should nearly match Tests: Actual mechanical issue (jumped timing gives odd manifold pressure)
Remove and inspect the sensor port for blockage Tests: Blocked sensor port (carbon/oil sludge)
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2017–2024 Chevrolet 2500: L5P MAP sensor soot caking ('Service Emissions System' countdown) — test first, then buy for this job.
The price range below is a national planning range for P0106 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $120
Labor$50 – $150
MAP sensor is usually one bolt and a connector. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0106 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →