P261B

P261B: Coolant Pump B Control Circuit Range/performance

For your specific vehicle: P261B on a 2010–2015 Toyota Prius

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

The second electric coolant pump is not performing right - the pump or its circuit is failing, so the engine can overheat.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 9 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check for Technical Service Bulletins for the specific vehicle - it may be a known issue with a known fix.
  2. Locate Coolant Pump B (usually mounted to the front or top of the engine, inside a wheel well, or against the bulkhead). Tests: Open in the circuit to the coolant pump
  3. Inspect the pump connector, wiring, and the pump relay and its connections for damage, corrosion, burn spots, or melted plastic - relays and their connections are the most common concern. Tests: Failed or corroded pump relay or relay connections
  4. Clean terminals with electrical contact cleaner and a plastic bristle brush, dry, and apply electrical grease.
  5. Clear the code with a scan tool; if it does not return, the connection was the problem.
  6. If it returns, disconnect the pump harness and check pump motor resistance with a digital multimeter against manufacturer specs - open or shorted means replace the coolant pump; a mechanically stuck impeller also means replacement.
  7. With the pump commanded on (scan tool actuator function), verify 12 V at the pump power supply circuit; repair wiring from the PCM or relay if missing.
  8. Verify a good ground at the pump with a test light while actuating it; wiggle the harness to catch intermittent connections.
  9. If all tests pass, the coolant pump has likely failed - replace it. PCM failure is unlikely.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$100 – $400
Labor$100 – $400

Electric coolant pump replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P261B ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Visual inspection and relay checks are DIY; pump resistance and circuit tests need a multimeter; PCM is shop-level.

Watch this repair on YouTube

Parts & tools

Cooling system toolkit — what the job actually takes

Torque specs: Thermostat housing bolts: typically 8–12 Nm. Aluminum threads strip easily — verify spec and use a torque wrench.

Pro tip: Bleed the cooling system per the factory procedure after refilling, or trapped air will overheat the engine and fake a “still broken” reading.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →