P0115: Engine coolant temperature sensor circuit malfunction
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonCooling system faults can lead to overheating. Watch the temp gauge; stop immediately if it climbs into the red.
The coolant temperature sensor has an electrical fault, so the computer doesn't know whether the engine is hot or cold. It runs rich to be safe and may run the cooling fans nonstop.
VW/Audi note (VCDS): A sensor reading -40 degrees means open circuit; reading maxed hot means shorted - the defaults point at the fault type.
Model notes: Do this job on a cold engine - opening the cooling system hot risks serious burns. Some vehicles have two coolant sensors (one for the ECM, one for the gauge); make sure you replace the right one.
Key facts
P0115 means engine coolant temperature sensor circuit malfunction. The coolant temperature sensor has an electrical fault, so the computer doesn't know whether the engine is hot or cold. It runs rich to be safe and may run the cooling fans nonstop. WrenchFair's published fair-price range for this repair is $25–$150 parts and $150–$400 labor at independent shops.
WrenchFair rates P0115 a 2-of-5 DIY difficulty (“The sensor is usually a simple threaded sender; do the job on a cold engine and top up coolant after.”) with a “Diagnose soon” driveability rating: Cooling system faults can lead to overheating. Watch the temp gauge; stop immediately if it climbs into the red. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
temperature gauge reading wrong or dead
cooling fans running constantly
poor fuel economy
rich running
low coolant
backfiring through tailpipe
engine dies/stalls
heavy black smoke from exhaust
cooling fans not coming on
Likely causes
Failed ECT sensor (most common)
Corroded connector - coolant seeps into these connectors over time
Damaged wiring
Low coolant level exposing the sensor to air instead of coolant
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Compare ECT reading to ambient on a cold engine - they should match
Check the connector for green corrosion, the classic ECT failure Tests: Corroded connector - coolant seeps into these connectors over time
Verify coolant level - a sensor in an air pocket reads wrong Tests: Low coolant level exposing the sensor to air instead of coolant
Test sensor resistance against the temp chart, or simply replace if the reading is implausible
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$25 – $150
Labor$150 – $400
Thermostat or sensor is typical; water pump work costs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0115 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The sensor is usually a simple threaded sender; do the job on a cold engine and top up coolant after.
Torque specs: Thermostat housing bolts: typically 8–12 Nm. Aluminum threads strip easily — verify spec and use a torque wrench.
Pro tip: Bleed the cooling system per the factory procedure after refilling, or trapped air will overheat the engine and fake a “still broken” reading.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →