Diagnose soonNot immediately dangerous, but slipping generates heat that wears the transmission - don't ignore it.
Your torque converter isn't locking up on the highway, so RPMs stay high and gas mileage suffers. Often a solenoid or old fluid.
Model notes: A fluid service is the reasonable first step; the TCC solenoid may be pan-accessible on some transmissions.
Key facts
P0741 means torque converter clutch circuit performance / stuck off. Your torque converter isn't locking up on the highway, so RPMs stay high and gas mileage suffers. Often a solenoid or old fluid. WrenchFair's published fair-price range for this repair is $85–$1200 parts and $300–$1500 labor at independent shops.
WrenchFair rates P0741 a 4-of-5 DIY difficulty (“Solenoid may be pan-accessible; converter is not.”) with a “Diagnose soon” driveability rating: Not immediately dangerous, but slipping generates heat that wears the transmission - don't ignore it. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2008–2016 Chrysler Town & Country (3.6L Pentastar V6, 3.8L V6, 4.0L V6) — 62TE stalls at stops — torque converter clutch solenoid:Owner-verified
Valve body is accessed through the transmission pan from below — the TCC solenoid swaps without pulling the transmission. Pan bolts come off with the fluid drained; the solenoid pack sits on the valve body.
Do this test first: Fluid service first
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0741 on the 2008–2016 Chrysler Town & Country — but the community-sourced 62TE stalls at stops — torque converter clutch solenoid note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
62TE transmission pan bolts: verify — A DIY video states 108 in-lbs (9 ft-lbs) for pan bolts — confirm against factory service info for the 62TE before torquing.
Tips
Learn the symptom pattern: the van randomly stalls at stoplights or when coming to a stop, only when warm, with zero codes — because the converter clutch stays locked instead of unlocking. Owners describe it as feeling like stopping a manual car in gear without pressing the clutch.
The in-car fix: replace the TCC solenoid (Mopar 5169313AA) plus a fluid and filter service — done through the pan, no transmission removal. A DIY video documents the exact procedure and a clean road test 20 days later.
Do this BEFORE authorizing a $4,000 shop rebuild — multiple owners were quoted full replacements for what turned out to be the solenoid.
Use ATF+4 only (Mopar or Valvoline ATF+4), and check the pan magnet for debris while you are in there: clutch material in the pan means the converter itself is shedding and the solenoid alone will not save it.
Related but different: a light-throttle shudder at 45-55 mph that stops the instant you tap the brake is the converter clutch slipping, not the solenoid — chryslerminivan.net owners confirm the brake-tap test distinguishes them.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Typical time: “A DIY video documents the exact procedure and a clean road test 20 days later.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
high cruise RPM
poor fuel economy
shudder
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Low or degraded transmission fluid - check level AND condition first; a fluid service alone fixes many cases 30 owner notes link this repair to P0741
Failed TCC solenoid or wiring fault 30 owner notes link this repair to P0741
Worn torque converter - TCC clutch friction material (converter replacement) 30 owner notes link this repair to P0741
Valve body wear/fault
Owner notes linked to P0741: 30 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Fluid service first Tests: Low or degraded transmission fluid - check level AND condition first; a fluid service…
Test the TCC solenoid Tests: Failed TCC solenoid or wiring fault
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2008–2016 Chrysler Town & Country: 62TE stalls at stops — torque converter clutch solenoid — test first, then buy for this job.
The price range below is a national planning range for P0741 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$85 – $1200
Labor$300 – $1500
Two paths, very different prices: TCC solenoid $85-$400 installed when it is pan-accessible; torque converter replacement ~$1,500 at an independent shop to $2,000+ (roughly 7 hours of labor; the converter itself runs $500 rebuilt to $800-$1,200 new) — a full transmission replacement runs $2,500-$7,500. The ranges above span all paths; match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0741 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Solenoid may be pan-accessible; converter is not.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →