Diagnose soonNeeds diagnosis - follow the diagnostic path.
Can I drive with P0700?
Can I drive with a P0700 code?
Short trips and gentle driving only, until you know the cause. Needs diagnosis - follow the diagnostic path. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0700?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Needs diagnosis - follow the diagnostic path.
Will P0700 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your transmission's computer found a problem and asked the engine computer to turn on the check engine light. This code alone doesn't say what's wrong - the real answer is in the transmission codes.
Model notes: Cheap code readers often cannot access the transmission module - if you only see P0700 with no detail, the tool is the limitation, not the car.
Key facts
P0700 means transmission control system malfunction (MIL request). Your transmission's computer found a problem and asked the engine computer to turn on the check engine light. This code alone doesn't say what's wrong - the real answer is in the transmission codes. WrenchFair's published fair-price range for this repair is $0–$0 parts and $80–$150 labor at independent shops.
WrenchFair rates P0700 a 2-of-5 DIY difficulty (“The job is reading the TCM codes - a generic reader may not see them; you need a tool that talks to the transmission module.”) with a “Diagnose soon” driveability rating: Needs diagnosis - follow the diagnostic path. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2006–2016 Chevrolet 2500 (6.6L Duramax V8 diesel (LBZ/LMM/LML) + Allison 1000) — Allison TCM failure — no-crank, no communication, U0101/U0100:Owner-verified
Driveway diagnosis, bench-repair part — the TCM unplugs from the Allison; the fix is usually a mail-in board repair or reman unit, no transmission teardown.
Do this test first: Read codes from the transmission control module specifically - not just the engine
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0700 on the 2006–2016 Chevrolet 2500 — but the community-sourced Allison TCM failure — no-crank, no communication, U0101/U0100 note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Tips
When the Allison TCM dies, the truck will not crank or start, will not shift, or sticks in limp mode (3rd gear) — with U0101/U0100 (lost communication with TCM), P0700, or P2669 stored in other modules. The T14/A50 TCMs in LMM/LML trucks have the highest failure rate, but LBZ trucks are hit too — GM PIP3605A documents the no-crank/no-communication pattern on 2006-2008 trucks.
The root causes are electrical, not mechanical. Jump-starting a dead truck or grounding a welder/battery charger to the TCM's heatsink fries the internal battery-ground wire bonds (pins 9 and 69). GM's bulletin is explicit: the heatsink is isolated from chassis ground, so never ground welding or charging equipment to it, and unplug the 80-way connector before any welding on the truck.
Heat and vibration kill them slowly too — the TCM lives in the hot engine bay (the LBZ mounts it on the fan shroud). Intermittent no-communication that worsens when hot is the classic pattern. Board-level rebuild services address the wire-bonding root cause rather than just swapping in a junkyard unit that will fail the same way.
Before condemning the TCM, rule out the NSBU (neutral safety/backup) switch — inspect it and its connector first, as module repair shops advise; a dead gear indicator plus no-start can be either the NSBU or the TCM. Then scan for U0101/U0100, P0700, P0827, and P2669.
If you replace rather than repair: a repaired original module is plug-and-play with no programming. A new or used TCM needs VIN programming — and any custom TCM tune must be backed up first, or it is gone.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
transmission symptoms per the underlying fault
possible limp mode
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Any transmission fault stored in the TCM, including sensor or solenoid faults (read TCM codes for the actual fault) 24 owner notes link this repair to P0700
TCM communication issue (rare - usually sets U-codes alongside) 24 owner notes link this repair to P0700
Owner notes linked to P0700: 24 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read codes from the transmission control module specifically - not just the engine Tests: Any transmission fault stored in the TCM, including sensor or solenoid faults (read TCM…
Diagnose the TCM code found there
Check transmission fluid level and condition while you are at it Tests: Any transmission fault stored in the TCM, including sensor or solenoid faults (read TCM…
Clear both modules' codes after repair and road test
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2006–2016 Chevrolet 2500: Allison TCM failure — no-crank, no communication, U0101/U0100 — test first, then buy for this job.
The price range below is a national planning range for P0700 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$0 – $0
Labor$80 – $150
P0700 carries no repair cost of its own — it is a MIL request from the transmission control module. Budget $80-$150 for a transmission diagnosis at an independent shop (dealers charge more); the real code(s) behind it determine the bill. National-average estimate for a diagnostic visit. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0700 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The job is reading the TCM codes - a generic reader may not see them; you need a tool that talks to the transmission module.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →