P0606

P0606 on a 2018–2018 Dodge Journey: ECM/PCM processor fault

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0606 on a 2018–2018 Dodge Journey · 2011–2019 Ford Fiesta · 2012–2018 Ford Focus

DIY difficulty 4/5

Your engine computer's internal self-test failed - the computer itself is reporting that it's faulty. This is serious, but rule out bad power first because computers lie when they're underfed.

Model notes: Get a second opinion before replacing an ECM for this code - it is one of the most misdiagnosed codes because power problems mimic it so well.

Key facts

☑ Before you buy parts — check these first:
On your 2018–2018 Dodge Journey (2.4L Tigershark I4) — Stall or no-start — PCM voltage-regulator recall U87: Factory-documented
Dealer-only repair — the PCM is replaced, not repaired. If your 2018 Journey stalls or cranks without starting, check this recall by VIN before paying for sensors or pumps.
Do this test first: Load-test ECM power and ground circuits - voltage drop under load reveals bad connections
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0606 on the 2018–2018 Dodge Journey — but the community-sourced Stall or no-start — PCM voltage-regulator recall U87 note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: FCA dealer service instructions (oemdtc) · recall record

Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0606: 3 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Load-test ECM power and ground circuits - voltage drop under load reveals bad connections Tests: Voltage supply problem mimicking processor fault
  2. Check for technical service bulletins - some processor faults have software fixes Tests: Voltage supply problem mimicking processor fault
  3. Inspect for water intrusion and overheating Tests: Overheating ECM
  4. Replace and program the ECM only after everything else is ruled out

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2018–2018 Dodge Journey: Stall or no-start — PCM voltage-regulator recall U87 — test first, then buy for this job.
The price range below is a national planning range for P0606 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$300 – $1200
Labor$150 – $400

Module replacement plus programming. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0606 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

4 of 5 — Prove power and ground perfect before condemning the module - modules are expensive.

Watch this repair on YouTube

Parts & tools

Electrical diagnosis toolkit — what the job actually takes

Torque specs: Module connectors: hand-tight until they click — never force them.

Pro tip: Check powers AND grounds before condemning a module — most “module failures” are wiring. Disconnect the battery before unplugging modules.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →