Drive safeNot urgent - the car runs fine and only cold-start emissions are affected.
The relay that switches the air pump on and off has an electrical problem in its control circuit. The pump itself may be perfectly fine - start with the relay, its fuse, and the wiring, because this code is about the switch, not the pump.
Key facts
P0418 means secondary Air Injection System Relay A Circuit. The relay that switches the air pump on and off has an electrical problem in its control circuit. The pump itself may be perfectly fine - start with the relay, its fuse, and the wiring, because this code is about the switch, not the pump. WrenchFair's published fair-price range for this repair is $15–$60 parts and $50–$100 labor at independent shops.
WrenchFair rates P0418 a 1-of-5 DIY difficulty (“Relay swap and fuse check - one of the easiest codes to diagnose.”) with a “Drive safe” driveability rating: Not urgent - the car runs fine and only cold-start emissions are affected. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 858 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Structure) — see the latest ones
On your 2010–2024 Toyota 4Runner (4.0L V6) — Secondary air injection pump/valve failure (P0418, P2440–P2445, limp mode):Owner-verified
The SAIS air pump sits on the front passenger side of the engine bay on the 5th-gen 4Runner, so everything is reachable without pulling the intake. Diagnose first: pull codes with any OBD-II reader. Stuck-valve codes (P2440/P2442 stuck open, P2441/P2443 stuck closed) usually trace back to the pump's internal foam filter disintegrating and the debris jamming the valves; the electrical P0418 points at the pump relay/circuit instead. Prevention, worth doing even if your codes haven't appeared: pop the pump cover with a T25 driver and a pry tool, pull out the crumbling foam filter, and fit a 25mm intake/Uni filter in its place. If the valves are already jammed, the two routes owners take are OEM pump + valve replacement (the dealer route, about a $2,000 parts-and-labor quote owners report) or the Hewitt Gen 2 bypass kit (about $500, owners report a ~30-minute install) — check your state's emissions rules before bypassing any emissions system. After the fix, clear the codes with your scanner; limp-mode codes sometimes need a manual erase before full power returns.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0418 on the 2010–2024 Toyota 4Runner — but the community-sourced Secondary air injection pump/valve failure (P0418, P2440–P2445, limp mode) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
SAIS pump cover and switching-valve fasteners: verify — No published torque specs in 4Runner owner DIYs for the SAIS hardware — snug by feel, never guess torque numbers.
Tips
The signature presentation: check engine light plus TRAC-off light, car goes into limp mode (no acceleration, 'go-cart speed') right after a cold start. On the 5th gen, that combo almost always means SAIS codes, not a traction problem — pull the codes before chasing anything else.
Root cause is usually mechanical, not electrical: the foam filter inside the air pump breaks apart with age and the debris gets sucked into the pump and jams the switching valves. The Uni/25mm intake filter swap is cheap prevention that owners do before codes ever appear.
If you just did belt or intake work and got a fresh P2445, check for a hose you knocked off the pump first — one owner's 'pump stuck off' was just a disconnected hose from his serpentine belt job, and reconnecting it plus erasing codes restored full power.
Clearing codes matters: erasing the stored code with a scanner is part of the fix — the limp-mode state doesn't always self-clear after you fix the underlying part.
Dealer quote owners report is around $2,000 for OEM pump + valves. The Hewitt Gen 2 bypass kit (~$500, ~30-min owner install) is the common alternative, but it disables an emissions system — check your state's emissions-inspection rules before going that route.
Once foam debris has jammed the valves, a filter swap alone won't save them — the filter mod is prevention. If the valves are already stuck, it's pump/valve replacement or the bypass kit.
Typical difficulty: Easy — based on 15 code guides for the sai repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light on
no noticeable driving symptoms
failed emissions test
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
failed air pump relay
blown fuse in the air pump circuit
open or shorted wiring in the relay control circuit
corroded relay socket or connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Check the related fuses and relays before condemning any part - an open fuse is a cheap fix. Tests: open or shorted wiring in the relay control circuit
Swap the air pump relay with an identical relay from a non-critical circuit and see if the code clears. Tests: blown fuse in the air pump circuit
Inspect the relay socket for corrosion or melted plastic. Tests: corroded relay socket or connector
Visually inspect the wiring, connectors, and hoses around the component for damage, corrosion, chafing, loose pins, or disconnection.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2010–2024 Toyota 4Runner: Secondary air injection pump/valve failure (P0418, P2440–P2445, limp mode) — test first, then buy for this job.
The price range below is a national planning range for P0418 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$15 – $60
Labor$50 – $100
Secondary air pump relay replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0418 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
1 of 5 — Relay swap and fuse check - one of the easiest codes to diagnose.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →