Community-sourced DIY repair guides for the 2010–2024 Toyota 4Runner, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Battery sits in the engine bay with a simple J-bolt hold-down. Owners debate group 24F vs the taller 27F — the 27F fits the stock tray and hold-down and gives more reserve capacity, but verify your chosen battery's height against the tie-down bracket. Pull the plastic catch tray and scrub any acid corrosion out of the fender while you're in there. Nothing else needs to come off; it's a 15-minute job with hand tools.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Torque specs
Battery terminal/hold-down hardware: verify — Snug per standard practice; confirm against the factory service manual if you want an exact value.
Tips
Don't panic when the engine stalls on the first start after a battery swap — the 5th gen relearns the throttle body on its own and starts normally the second time; owners consider this normal, not a fault.
You'll need to reset the clock and compass zone after power is restored.
Owners warn the stock alternator charges at a modest rate, so an AGM battery won't stay fully healthy long-term without a voltage-boosting diode; stick with a flooded battery if you run the stock setup.
Clean the cable terminals with a wire brush and the plastic catch tray of any spilled acid — corrosion there quietly eats the fender.
Front brake pads & rotors Owner-verified(4.0L V6 (1GR-FE))
Front calipers are fixed 4-piston units, so for a pads-only swap you don't remove the caliper: pull the two retaining-pin clips, slide the pins out, and remove the anti-rattle spring (feed the pin hoop from the outside of the rotor toward the inside on reassembly). For rotors, remove the two large caliper bolts and hang the caliper with a bungee — never let it dangle on the brake hose. Rotors can rust-seat to the hub and need a rubber mallet; remove the master-cylinder cap before compressing pistons.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Caliper mounting bolts: verify — Owners quote 74 lb-ft from forum/YouTube writeups, but confirm against the factory service manual before torquing — these are safety-critical bolts.
Lug nuts: verify — Confirm against the owner's manual/factory service info before torquing.
Tips
OEM pads plus new shims and fresh caliper grease is the community-recommended combo if you want factory pedal feel — owners say it costs little more than aftermarket.
Check rotor thickness against spec (standard 32.0 mm front, minimum 29.0 mm); if rotors are smooth, unwarped, and above minimum, pads-only is fine.
Clean the rust off the rotor-to-hub mating surface so the next set doesn't seize on; owners who skip this fight the rotor off next time.
Bedding-in matters on a truck this heavy — a few firm stops from moderate speed after installation seats the pads and prevents early shudder.
Owners say if you can do a brake job, you can do this — it's the same front-end teardown plus four bolts. Remove the wheel, caliper (hang it, don't strain the brake line), and rotor; unbolt the four bolts holding the hub to the back of the steering knuckle (open-end wrench only, very little room back there). Pop the dust cap, remove the cotter pin/nut cap and the large axle nut (impact gun works best), then tap the axle stub gently with soft wood or a brass hammer — never hammer the threads directly — and work the assembly off with a pry bar around the flange. The dust shield drops free when the hub comes out, so plan an extra pair of hands for reassembly.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
CV axle nut: verify — Community sources cite 173 lb-ft; confirm against the factory service manual before torquing — this is critical to keeping the bearing pressed on the hub.
Hub mounting bolts: verify — Confirm against the factory service manual before torquing.
Tips
Buy the complete pre-pressed hub assembly (OEM/NSK/Koyo), not a bare bearing — pressing a bearing into your old hub is far more work and owners say it's a false economy.
Re-torque the CV axle nut with a calibrated torque wrench to factory spec (community sources cite 173 lb-ft — confirm against the factory service manual); a loose axle nut can un-seat the bearing press and the new hub will feel loose almost immediately.
Diagnose by sound and feel first: the classic sign is a humming/growling that changes with road speed and load, and swerving side to side in an empty parking lot can reveal which side it is.
Do both sides' ABS/hub bolts inspection while you're in — the rear hubs are press-in style and a bigger job, so catching front wear early is the cheap win.
On the 1GR-FE the thermostat is sold only as an assembly with its plastic housing — you can't buy just the thermostat from Toyota. The housing sits at the lower radiator hose inlet; disconnect the lower hose, unbolt the housing, and swap the assembly with a new gasket. The factory plastic housing is a known weak point (the fingers that hold the thermostat can break and the flat o-ring can weep), so inspect it closely rather than reusing a marginal one. Do this with a coolant drain and inspect the hoses and clamps while you're in there.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
Thermostat housing bolts: verify — Confirm against the factory service manual before torquing — plastic housing, easy to crack.
Tips
Buy OEM or Aisin; owners who tried cheap aftermarket thermostats report problems, and the Aisin assembly runs about $30 vs ~$50 for Toyota.
Check the jiggle/bleed valve orientation on install (owners note it must be positioned correctly, typically at 6 o'clock) or you'll fight trapped air.
In salt states, the lower radiator hose clamps rot first — owners in the Northeast say to budget new clamps, and replace hoses while the system is drained if they're soft or bulging.
Refill only with Toyota pink Super Long Life coolant or a verified SLLC-compatible pink alternative, and burp the system thoroughly to avoid a false P0128 right after the job.
The passenger-side bank is straightforward once the air intake tube is pulled aside. The driver-side bank sits under the intake plenum overhang: owners unbolt the plenum's support brackets and swing them aside to reach the coils and plugs rather than pulling the manifold. The driver-side front plug's harness connector is the tightest spot and needs patience to wiggle free. Blow compressed air into each plug well before pulling plugs so grit can't fall into the cylinders.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Torque specs
Spark plugs: verify — Confirm against the factory service manual for the dual VVT-i 1GR-FE before torquing — aluminum heads, and owners report some factory plugs were barely tight.
Coil hold-down bolts: verify — Confirm against the factory service manual before torquing.
Tips
Only run Denso or NGK plugs matched to the part numbers in the owner's manual — owners warn Toyota is picky and parts-counter 'equivalents' can cause issues; some 1GR-FEs came from the factory with Denso on one bank and NGK on the other.
Change plugs every 120k miles or 10 years per Toyota; owners recommend doing it earlier rather than later since seized threads in aluminum heads are worse than worn plugs.
Don't fully remove the intake plenum brackets on the driver side — just remove the top bolts and the 10mm AFR-sensor harness bolt, loosen the lower bolts, and swing the bracket aside; getting the lower bolts re-aligned is the painful part.
Hand-thread each plug carefully into the aluminum heads, change them one at a time so no hole is left open, and put a dab of dielectric grease inside the coil boots.
Transmission fluid service Owner-verified(4.0L V6 (1GR-FE))
The A750F has no dipstick — level is set through three plugs: drain, overflow/check, and a fill plug up on the passenger side of the case. Always loosen the FILL plug first, before you drain a drop: if the fill plug is seized after you've drained the pan, the truck isn't drivable. Fill with a length of vinyl tubing run up into the engine bay, then set the level with the engine running on perfectly level ground and ATF temp at 115 F (46 C), read via a scan tool's ATF temp PID or the OBD pin-jump temp-check mode, letting excess trickle out of the overflow tube.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Fill plug: verify — Owners quote 27 lb-ft / 37 N-m from community writeups, but confirm against the factory service manual before torquing.
Drain/check plugs and pan bolts: verify — Owners quote 15-21 lb-ft (drain/check) and 62 in-lb (pan); confirm against the factory service manual before torquing.
Tips
Use Toyota Genuine ATF WS only — owners are unanimous that this transmission does not tolerate fluid substitutes.
A drain-and-fill is only about 3 quarts of the total capacity; owners who want a fresher fluid simply repeat the drain-and-fill across several services rather than power-flushing.
Always use a fresh crush washer on the drain and check plugs (they're the same part number) or you'll chase seeps.
Do the job on a cold, level vehicle, shift slowly through every gear to circulate fluid before the level check, and don't overthink being a few ounces off — owners note the trans tolerates small variations, but the level-check temperature window is the part that actually matters.
The X-REAS cross-linked system runs hydraulic lines diagonally across the frame (driver-front to passenger-rear and vice versa) with accumulator valves bolted to the frame rails. It is a purely mechanical system with no sensors, wiring, or dash electronics to deal with, so there is no warning light or recalibration after removal. Pull the old lines and the frame-rail accumulators along with the shocks — they unbolt with basic hand tools. Front coil springs are under heavy preload; most owners have a shop swap the spring onto the new strut with a wall-mounted compressor rather than fighting rental clamps.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Torque specs
Suspension fasteners: verify — No torque-critical fasteners confirmed from a forum source — confirm strut, UCA, and shock-mount values against factory service info before torquing.
Tips
When one corner starts weeping — owners report leaks commonly starting around 50,000–70,000 miles — the whole system is on the clock; a weep only gets worse and the handling progressively wallows in turns. There is no individual shock repair: it is full system replacement or conversion.
You do not need a conversion kit or plugs: owners who pulled the system report the hydraulic unions self-seal when disconnected, and the lines come out as a handful of 10mm bolts and clips holding roughly 20 feet of line. Pull the accumulators too rather than leaving dead weight on the frame.
Do the whole system in one job, not one corner at a time — the cross-linked hydraulics mean a half-swapped system will not behave. Any standard 5th-gen setup works: owners run everything from stock non-Limited takeoffs to Bilstein 4600/5100s or OME.
No sensors means no dash lights, but it also means no resale value argument for keeping a dead X-REAS — owners who tried replacing with like-for-like OEM X-REAS report the same weep cycle repeating.
Check whether your factory extended warranty covers it before converting: multiple owners report the X-REAS assembly is covered as a system component even though ordinary shocks are wear items.
Driveline clunk on takeoff or stopping (slip-yoke grease) Owner-verified(4.0L V6 (1GR-FE))
No lift needed — roll the truck a few inches to rotate each shaft so the zerks face down. The 5th gen comes from the factory with plugged holes where the zerks go, so buy your own fittings and thread them in: one per U-joint, plus one for each slip joint front and rear. The front shaft is reachable from the passenger side without removing skid plates. A LockNLube-style locking coupler on the grease gun makes the cramped fittings manageable.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Driveshaft hardware: verify — Driveshaft bolt torque not confirmed from a forum source — confirm against factory service info if the shaft is removed.
Tips
Diagnose by feel: a dull thud like someone tapping your bumper when you come to a stop or pull away is the classic dry slip-yoke symptom — owners report it even on low-mileage trucks, so do not assume it means a worn drivetrain.
Use moly-lithium (moly-fortified) grease on the slip joints, plain NLGI-2 lithium EP on the U-joints. For the yokes, 4–5 pumps is the working range — the goal is lubrication, not packing the cavity full.
Critical step owners learned the hard way: after greasing the slip joint, remove the zerk and bounce the suspension or compress the shaft to let excess grease and trapped air escape, then reinstall the fitting. Over-packing hydraulic-locks the yoke — one documented case collapsed the rear pinion crush sleeve and destroyed the ring and pinion.
If a few pump cycles no longer quiet the clunk, the old grease may be dried and caked inside — pulling the rear shaft, cleaning the slip joint by hand, and repacking is the deeper fix.
Make it a routine: owners who grease every oil change (roughly 10k miles) or at least twice a year report the clunk never returns.
The shutter valves are on the KDSS accumulator housing under the body on the driver's side. The truck needs to sit at normal ride height on flat ground — measure center-of-hub to fender lip on both sides first so you can track the change. Do not touch the solenoid valves or pull the KDSS fuse; those do not calibrate the system.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Typical time: “The documented recalibration: crack the two shutter valves about 2 turns — never more than 2.5 — let the system equalize and settle for 20 minutes, rocking the truck gently, then close the valves and re-measure.” — as written in the note. First-timers often take twice this.
Torque specs
KDSS shutter valves: verify — No torque value confirmed from a forum source — valves are backed out 1–2.5 turns and re-seated by hand; confirm against factory service info rather than overtightening.
Tips
Toyota's own spec allows up to about 3/4 inch of lean on KDSS trucks, so confirm it is actually a KDSS problem and not a lift-install asymmetry or a worn spring before touching the hydraulics.
The documented recalibration: crack the two shutter valves about 2 turns — never more than 2.5 — let the system equalize and settle for 20 minutes, rocking the truck gently, then close the valves and re-measure.
If the lean persists after one equalization, the refinement owners converged on is to jack the high side up past level (compressing that spring slightly beyond even) before closing the valves — one documented case took a 2-inch difference down to a quarter inch this way.
Backing the shutter valves out too far lets high-pressure fluid out and air in, which turns a driveway adjustment into a bleed-and-repressurize job at a dealer — treat the 2-turn limit as a hard stop.
Expect the lean to return after lifting the truck: the KDSS sway-bar angles change with ride height, which is why lifted trucks lean. Spacer kits for the rear bar exist if the lean follows a lift.
Frame rust inspection and prevention (5th gen) Owner-verified(4.0L V6 (1GR-FE))
The frame is fully visible from underneath — no disassembly needed, though pulling the skid plates and spare tire gives clear access for the full inspection and wash. The 5th gen uses a boxed frame, which is stronger than a C-channel but hides rust inside the rails. A lift or good jack stands make the job far easier.
Torque specs
Skid plate hardware (if removed): verify — No torque-critical fasteners in the inspection and coating procedure — confirm skid-plate values against factory service info if removed.
Tips
Check the 4Runner-specific rust traps first: the front radiator support crossmember where the tow loops mount (owners report this disintegrating first), the body mounts and the frame around them, and the passenger-side frame rail that stays wet all summer from the AC condensation drain.
Ignore a dealer's 'factory treated' claim — rust-belt owners document 5th gens rusting through within 5–6 years of salt exposure regardless. There is no 5th-gen 4Runner frame replacement campaign; prevention is the entire game.
The critical step owners stress: wash the inside of the boxed frame rails with a hose until the water runs clear, then drive a few days to dry — rustproofing over trapped salt locks the problem in. Fluid Film sells a spray-can kit with a tube that reaches inside the rails.
Owner consensus for ongoing protection is an annual wet-film treatment (Fluid Film or Woolwax) inside and outside the frame, with touch-ups on abrasion zones — front of the rear axle, rear shock mounts, lower trailing links. Expect to redo it yearly; there is no spray-and-forget solution.
Once rust goes puffy it acts like a salt-water sponge and accelerates — descale the loose stuff with a wire brush before coating rather than spraying over it.
Alternator failure (brush replacement vs new unit) Owner-verified(4.0L V6 (1GR-FE))
The alternator is reachable from the engine bay after removing the serpentine belt and under cover — owners consider it a moderate driveway job with basic sockets. Before buying anything, have the charging system tested free at a parts store and confirm with a multimeter: at least 13.5 volts across the battery terminals with the engine running means the alternator is still doing its job.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Alternator mounting hardware: verify — Alternator bolt torque not confirmed from a forum source — confirm against factory service info before torquing.
Tips
Do not preemptively replace it: owner consensus is that these Denso alternators rarely fail and routinely last to 180,000 miles or more. When the battery warning light does come on, the alternator has typically been undercharging below 12 volts for some time — check the battery first, then the alternator.
The usual failure mode is worn brushes, not a dead unit — a brush set costs around $20 and owners report this being the only failure they have seen on these alternators. Rebuild the brushes before buying a whole unit.
If you do replace, be picky about the source: owners warn that cheap remanufactured units are hit-or-miss, and one thread documents a reman failing right out of the box. A Denso reman from a reputable seller or a used low-mile OEM unit are the paths owners trust.
While the belt is off for access, do the serpentine belt and check the idler pulleys — several owners bundle it as same-labor maintenance.
If you jump-start a dying system and it immediately dies again, do not keep jumping: charge the battery fully before testing the alternator, or a good battery test will mask as a bad alternator.
Secondary air injection pump/valve failure (P0418, P2440–P2445, limp mode) Owner-verified(4.0L V6)
The SAIS air pump sits on the front passenger side of the engine bay on the 5th-gen 4Runner, so everything is reachable without pulling the intake. Diagnose first: pull codes with any OBD-II reader. Stuck-valve codes (P2440/P2442 stuck open, P2441/P2443 stuck closed) usually trace back to the pump's internal foam filter disintegrating and the debris jamming the valves; the electrical P0418 points at the pump relay/circuit instead. Prevention, worth doing even if your codes haven't appeared: pop the pump cover with a T25 driver and a pry tool, pull out the crumbling foam filter, and fit a 25mm intake/Uni filter in its place. If the valves are already jammed, the two routes owners take are OEM pump + valve replacement (the dealer route, about a $2,000 parts-and-labor quote owners report) or the Hewitt Gen 2 bypass kit (about $500, owners report a ~30-minute install) — check your state's emissions rules before bypassing any emissions system. After the fix, clear the codes with your scanner; limp-mode codes sometimes need a manual erase before full power returns.
Typical difficulty: Easy — based on 15 code guides for the sai repair area (an area-level estimate, not this exact job).
Torque specs
SAIS pump cover and switching-valve fasteners: verify — No published torque specs in 4Runner owner DIYs for the SAIS hardware — snug by feel, never guess torque numbers.
Tips
The signature presentation: check engine light plus TRAC-off light, car goes into limp mode (no acceleration, 'go-cart speed') right after a cold start. On the 5th gen, that combo almost always means SAIS codes, not a traction problem — pull the codes before chasing anything else.
Root cause is usually mechanical, not electrical: the foam filter inside the air pump breaks apart with age and the debris gets sucked into the pump and jams the switching valves. The Uni/25mm intake filter swap is cheap prevention that owners do before codes ever appear.
If you just did belt or intake work and got a fresh P2445, check for a hose you knocked off the pump first — one owner's 'pump stuck off' was just a disconnected hose from his serpentine belt job, and reconnecting it plus erasing codes restored full power.
Clearing codes matters: erasing the stored code with a scanner is part of the fix — the limp-mode state doesn't always self-clear after you fix the underlying part.
Dealer quote owners report is around $2,000 for OEM pump + valves. The Hewitt Gen 2 bypass kit (~$500, ~30-min owner install) is the common alternative, but it disables an emissions system — check your state's emissions-inspection rules before going that route.
Once foam debris has jammed the valves, a filter swap alone won't save them — the filter mod is prevention. If the valves are already stuck, it's pump/valve replacement or the bypass kit.
Front differential needle bearing growl (ECGS bushing fix) Owner-verified(4.0L V6)
Confirm the diagnosis with the 4HI test: drive 35–45 mph in 2WD and note the growl/vibration, then shift into 4HI where safe — if the noise goes away in 4HI and comes back in 2WD, it's the driver-side front-diff needle bearing. The fix: pull the driver-side CV axle (35mm axle nut at 174 ft-lb), slide the ECGS removal tool behind the factory needle bearing (Toyota 90364-35010 / 90364-35008) and extract it with a slide hammer, then drive the T8CS PTFE bushing in flush with the install tool. Replace the driver-side axle seal while you're in there — it's right there and the old seal is usually shot. ECGS lists the bushing as NOT fitting AWD 4Runners (e.g. Limited full-time 4WD), so check fitment against your trim.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Front drive-axle nut (35mm): 174 ft-lb — From the 5th-gen torque-spec table (Trail4Runner.com). Re-torque on reinstall after the CV axle goes back in.
Front differential drain / fill plugs: 48 / 29 ft-lb — Same 5th-gen torque-spec table. Handy if you drain the diff while the axle is out.
Tips
The 4HI test is the best quick indicator owners have: 35–45 mph growl in 2WD that disappears in 4HI and returns in 2WD is the needle bearing. Tires, wheel bearings, and CV axles can mimic it, so do this test before ordering parts.
It hits lifted trucks most often, but stock trucks get it too — one owner reports being 2-for-4 across four 5th-gen 4Runners going back to 2014. Don't rule it out just because you're not lifted.
It's annoying, not urgent: owners report zero cases of the bearing failing catastrophically and grenading the diff. One owner drove 3,000 miles on the noise before fixing it.
Driver side only — the passenger side of the 8-inch clamshell uses a ball bearing that doesn't have this failure mode. The bushing only replaces the driver-side needle bearing.
Budget: the ECGS bushing runs about $60 plus $75 for the removal/install tools; one owner reports about $400 parts and labor max if you pay a shop. DIY saves most of that.
Moderate-skill job with one quirk: the extraction tool is a tight fit in the diff — the YouTube walkthrough shows grinding one edge of the tool down slightly to get it seated. A helper and a slide hammer set make this much easier.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
DIY-friendliness scorecard
Score: 89/100 — DIY-friendly
Special tools mentioned in the notes (4, −16): torque wrench, press, scan tool with live data, multimeter.
Documented dealer-only steps (0, −0): none documented in the notes — that does not mean none exist.
How this is scored (mechanical, no opinion): start at 100; −4 per distinct special tool mentioned in the notes (max −28); −15 per documented dealer-only step (max −30); note-volume band: 15+ notes +10, 8–14 +5, 4–7 +0. Bands: 85+ DIY-friendly · 65–84 DIY with care · 40–64 Experienced DIY only · below 40 Think twice. Pilot rubric — flagged for Robbie’s eyeball before any scale-up.
NHTSA recorded 217 complaints for the 2010–2024 Toyota 4Runner. 2012 was the worst year (96 complaints). Most-reported areas: air bags, unknown or other, electrical system.
17V763000 (29/11/2017) — STRUCTURE:BODY:HOOD Southeast Toyota Distributors, LLC (SET) is recalling certain 2015-2018 Toyota 4Runner vehicles equipped with an accessory Billet Grille Overlay installed by SET or provided by SET and installed by SET dealers. The U-nut that secures the overlay grille may fracture…
24V548000 (23/07/2024) — EQUIPMENT:OTHER:LABELS Gulf States Toyota, Inc. (GST) is recalling certain Toyota 2023 GR Supra, 2024 4 Runner, Corolla, Grand Highlander, Grand Highlander Hybrid, Land Cruiser Hybrid, Tacoma, Tacoma Hybrid, 2023-2024 BZ4X, Corolla Cross Hybrid, GR Corolla, GR86, Highlander, Highlander Hybrid, Prius, Prius…
12V120000 (23/03/2012) — EQUIPMENT:ELECTRICAL GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2012 4RUNNER AND SIENNA VEHICLES, EQUIPPED WITH NON-ORIGINAL EQUIPMENT REMOTE ENGINE STARTERS. A MALFUNCTION IN THE AUDIOVOX ELECTRONICS BRAND REMOTE ENGINE STARTER MODULE CAN PREVENT NORMAL COMMUNICATION OF THE VEHICLES CONTROLLER AREA…
16V236000 (22/04/2016) — TIRES Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2016 Toyota Yaris, Rav4, Land Cruiser and 4Runner vehicles, and Scion FR-S, iM, and TC vehicles manufactured January 28, 2016, to March 14, 2016. The Load Carrying Capacity Modification Label…
16V937000 (21/12/2016) — AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Toyota Motor Engineering & Manufacturing (Toyota) is recalling one 2016 Toyota 4Runner vehicle manufactured November 1, 2016 and one 2017 Lexus GX460 vehicle manufactured November 16, 2016. The affected vehicles are equipped with Takata PSPI-LD front passenger air bag inflators…
16V228000 (20/04/2016) — EQUIPMENT:OTHER:LABELS Gulf States Toyota, Inc. (Gulf States) is recalling certain model year 2015-2016 Toyota 4Runner vehicles manufactured September 22, 2014, to March 23, 2016 and equipped with accessories installed by Gulf States. The Load Carrying Capacity Modification Label may not reflect…
15 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
NHTSA has published 858 manufacturer communications (service bulletins, dealer notices) covering the 2010–2024 Toyota 4Runner.
Most cited systems: Equipment (463), Electrical System (196), Structure (101), Equipment Adaptive/Mobility (44), Unknown Or Other (38).
Latest bulletins:
T-SB-0002-25 Rev1 (Aug 2026) — Structure
T-SB-0106-22 Rev2 (Jan 2026) — Electrical System
T-TT-0788-25 Rev1 (Jan 2026) — Service Brakes
NHTSA also opened 1 defect investigation covering these years.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.