P0351

P0351 on a 2011–2019 Ford Explorer: Ignition coil 'A' primary/secondary circuit

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0351 on a 2006–2011 BMW 3 Series · 2012–2018 BMW 3 Series · 2011–2019 Ford Explorer · 2011–2019 Hyundai Sonata · 2011–2021 Jeep Grand Cherokee · 2013–2018 Nissan Altima
Show all 11 vehicles with this code

2019–2026 Ram 1500 · 2013–2020 Subaru BRZ · 2013–2019 Subaru Outback · 2018–2024 Toyota Camry · 2005–2015 Toyota Tacoma

DIY difficulty 2/5

The ignition coil for cylinder 1 has an electrical fault.

Key facts

☑ Before you buy parts — check these first:
On your 2011–2019 Ford Explorer (3.5L V6) — Spark plugs and ignition coils: Owner-verified
Transverse 3.5L V6 NA: the front 3 plugs/coils are directly accessible, but the rear bank sits under the upper intake plenum. Remove the air snorkel, disconnect the throttle body from the intake, then remove the plenum — 7 visible bolts plus one hidden bolt under the throttle body (easy to miss). Plan on a new intake plenum gasket for reassembly. Job takes roughly 2 hours, most of it hunting the hidden bolt. Front 3 = easy, rear 3 = the whole job.
Do this test first: Swap coil A with another cylinder's coil
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0351 on the 2011–2019 Ford Explorer — but the community-sourced Spark plugs and ignition coils note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: ExplorerForum: 2011 XLT 3.5L misfire thread — intake removal for rear plugs (7 visible bolts + 1 hidden under throttle body) · FordTechMakuloco (BSG Automotive): 2011–2017 Ford 3.5L/3.7L Duratec spark plug replacement — 133 in-lbs plug torque, 89 in-lbs + 45° intake torque, 0.051 in gap · TRQ: How to Replace Spark Plugs 2011–2019 Ford Explorer (3.5L V6), done on a 2013 Limited 3.5L · ExplorerForum: 2011 spark plug thread — new gasket needed when reassembling plenum after rear-bank access · ExplorerForum: Explorer Sport 3.5L EcoBoost plug job — no intake manifold removal needed

Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).

Typical time: “Job takes roughly 2 hours, most of it hunting the hidden bolt.” — as written in the note. First-timers often take twice this.

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0351: 11 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Swap coil A with another cylinder's coil
  2. Check the coil connector for corrosion Tests: Damaged wiring or corroded connector
  3. Test coil power and ground
  4. Replace the coil if the fault follows it

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2011–2019 Ford Explorer: Spark plugs and ignition coils — test first, then buy for this job.

Expensive fork: Fuel injector, then compression test — if the misfire stays on the same cylinder after a fresh plug and a swapped coil. The price range below is a national planning range for P0351 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $150
Labor$50 – $150

Ignition coil replacement (coil A). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0351 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Swap the coil with another cylinder - if the code follows, the coil is bad.

Watch this repair on YouTube

Parts & tools

Spark plug & coil toolkit — what the job actually takes

Torque specs: Gasket-seat plugs: typically 20–30 Nm (15–22 lb-ft). Tapered-seat plugs: typically 11–18 Nm. Always verify against your engine’s factory spec — over-torquing strips aluminum threads.

Pro tip: Blow out the plug wells with compressed air BEFORE removing the plugs, so debris can’t fall into the cylinders.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →