Community-sourced DIY repair guides for the 2011–2019 Ford Explorer, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Spark plugs and ignition coils Owner-verified(3.5L V6)
Transverse 3.5L V6 NA: the front 3 plugs/coils are directly accessible, but the rear bank sits under the upper intake plenum. Remove the air snorkel, disconnect the throttle body from the intake, then remove the plenum — 7 visible bolts plus one hidden bolt under the throttle body (easy to miss). Plan on a new intake plenum gasket for reassembly. Job takes roughly 2 hours, most of it hunting the hidden bolt. Front 3 = easy, rear 3 = the whole job.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Typical time: “Job takes roughly 2 hours, most of it hunting the hidden bolt.” — as written in the note. First-timers often take twice this.
Torque specs
Spark plugs: 133 in-lbs (11 ft-lbs) — Gap 0.051 in (factory gap range 0.051–0.057 in per owner forum). Install on a cold engine; start plugs by hand to avoid cross-threading.
Intake plenum bolts: 89 in-lbs + 45-degree additional turn — Follow the factory torque sequence for the plenum; two-step torque-plus-angle.
Ignition coil bolts: verify — Confirm against factory service info for this vehicle.
Tips
Many replacement plugs (Motorcraft/NGK) have a silver anti-seize-style coating on the threads — do NOT add additional anti-seize, it will over-torque plugs in the aluminum heads.
Replace the intake plenum gasket when reassembling; reuse risks a vacuum leak.
The EcoBoost 3.5L (Sport) is different: owners report no intake removal is needed for its plugs — only the turbo charge pipe's bolt and clamps need to come off. This note covers the NA 3.5L.
Blow compressed air into each plug well before removing plugs so debris can't fall into the cylinder.
Common trigger: P0301–P0306 misfires where new plugs alone don't fix it — forum owners report the coil for the misfiring cylinder is often the real culprit.
Front brake pads and rotors Owner-verified(3.5L V6)
Remove the wheel (19mm lug nuts). Unbolt the two caliper slide-pin bolts (17mm socket/wrench) and hang the dual-piston caliper from the strut — never let it hang by the flex hose. Remove the two 18mm caliper bracket bolts from the knuckle, lift off the bracket, then remove the T40 Torx rotor hold-down screw; knock the rusted rotor off the hub (a lug nut threaded on hand-tight keeps it from flying). Clean the hub face, install the new rotor, then reinstall the bracket with fresh medium-strength threadlocker. Compress the dual pistons with the bleeder screw cracked open so dirty fluid bleeds out instead of being pushed back into the ABS module.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Caliper bracket bolts (18mm): 122 ft-lbs — Apply fresh medium-strength threadlocker to the bolt threads on reinstall; bottom bolts out, then torque.
Caliper slide-pin bolts (17mm): 55 ft-lbs (14 in rotor); 53 ft-lbs (13 in rotor) — Top pin has a rubber boot that must seat in the top slider; clean and re-grease pins with silicone paste; inspect boots for pinholes/tears.
Wheel lug nuts: 100 ft-lbs (135 Nm) — Per the 2014 and 2019 Explorer Owner's Guides. Tighten in a star pattern, ground the vehicle, then re-torque. Note: 2020+ Explorers use 150 ft-lbs — do not confuse with this generation.
Tips
Slide-pin torque differs by rotor size — 14 in rotors take 55 ft-lbs, 13 in rotors take 53 ft-lbs. Check your rotor diameter before torquing.
Factory threadlocker on the bracket bolts: wire-wheel the old threadlock off and apply fresh medium-strength threadlocker on reinstall.
1A Auto's video notes this vehicle uses DOT 4 brake fluid — check the master cylinder cap and top off to the max line after the job, then pump the pedal to seat the pads.
Clean new rotors with brake cleaner before install to remove the storage oil coating; clean the hub-to-rotor mating face so the rotor seats flush.
The battery is buried at the driver-side rear of the engine bay, tucked under the windshield cowl panel — you cannot just unbolt it from above. Pop the push clips/fasteners and remove (or lift aside) the cowl cover over the battery to expose it; forum owners note the whole cover comes off in about a minute. Disconnect the negative cable first, then the positive; remove the battery hold-down clamp; lift the old battery out by its handle. Install in reverse: seat the battery, reinstall the hold-down, connect positive first, then negative.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Typical time: “Per the 2013 Owner's Manual (quoted by ExplorerForum members): after battery replacement the BMS needs ~8 hours of undisturbed vehicle sleep (key off, doors closed) to relearn the new battery's state of charge; until…” — as written in the note. First-timers often take twice this.
Torque specs
Battery terminal clamps: verify — Confirm against factory service info for this vehicle; snug clamps so they cannot twist on the posts, do not over-tighten.
Battery hold-down clamp bolt: verify — Confirm against factory service info for this vehicle.
Tips
This generation has a Battery Management System (BMS). Per the 2013 Owner's Manual (quoted by ExplorerForum members): after battery replacement the BMS needs ~8 hours of undisturbed vehicle sleep (key off, doors closed) to relearn the new battery's state of charge; until then it may disable features like rear defrost, heated seats, climate fan, heated wheel, or audio/nav.
A scan tool (e.g., FORScan) can perform the BMS reset immediately instead of waiting out the 8-hour sleep.
Terminal order: negative off first, negative on last. Connect positive first when installing the new battery.
Use a Group 65 battery matching the original size/type; verify against the label in the vehicle or parts catalog — do not guess the group size.
PTU failure and fluid service Owner-verified(3.5L Ti-VCT V6, 3.5L EcoBoost V6, 2.0L EcoBoost I4, 2.3L EcoBoost I4)
Bolted directly to the transmission at the front of the vehicle. The drain plug is reachable from underneath but access is tight — one owner stripped the plug and had to drop the catalytic converter pipe for room. The vent tube up top is the fill path.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
PTU drain/fill plug: verify — Plug torque not confirmed from a forum source — confirm against factory service info before torquing.
Tips
The 5th gen has no transfer case — the PTU is a purely mechanical gear device bolted to the transmission that borrows power for the rear axle. It fails more often than the rear drive unit because it holds very little oil, has a small case with limited cooling, sits in a hot spot, and Ford lists no fluid-change interval.
Owner consensus is a drain-and-fill every 30,000–50,000 miles (closer to 30k) as prevention. A full PTU replacement runs over $3,000, so the service pays for itself many times over. One long-term owner did two services in 110k miles and reported the fluid still looked fine — not every unit is doomed, but the interval is cheap insurance.
Service method: drain from the bottom plug, refill through the vent tube. The refill is slow — let the fluid work its way down and let air burp out. One owner extended the vent tube up near the master cylinder so future services can be done from above without crawling under.
If the PTU is already leaking at the seals, owners have documented the part numbers: 7E5Z-7H469B crush seal between transmission and PTU, DB5Z-7275-E seal kit for the axle side, and 7T4Z-7R284-A for the PTU output shaft seal. Do all of them while it is apart.
Whining or grinding from the front that changes with vehicle speed (not engine RPM) points at the PTU or a wheel bearing. A failing PTU left alone can take the transmission seals with it — the leak between the two is the classic sign.
Internal water pump — timing-chain-driven, leaks into the oil Owner-verified(3.5L Ti-VCT V6, 3.5L EcoBoost V6)
Inside the engine, driven by the timing chain — the front timing cover comes off to reach it. Owners describe it as a tedious, bend-over-the-fender job rather than a technically difficult one.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Timing components and water pump bolts: verify — Torque specs for timing components not confirmed from a forum source — confirm against factory service info before torquing. Cam phaser bolts are torque-to-yield single-use.
Tips
The 3.5L water pump is driven by the timing chain inside the engine. When the pump seal fails inward, coolant drains straight into the oil pan — and these trucks have no low-coolant-level sensor, so owners recommend watching the reservoir level yourself as the early warning.
Distinguish the two failure modes: an external leak (weep hole dripping, visible coolant) is a repair-soon job; an internal leak (milky oil, rising oil level, unexplained coolant loss with no puddle) is stop-driving-now — it kills bearings fast. One owner's 2013 started dripping from the weep hole at 150k and was caught in time.
Do the timing chain while you are in there. The labor overlaps almost completely, and owners report the pump-only job at an independent shop around $1,500–$1,800 versus $2,500–$3,600+ with the full timing set; one dealer quote hit $3,430. DIY parts for pump plus timing kit run roughly $550–$600.
Ford redesigned the pump for the 2012 model year with a beefed-up shaft and dual-tooth sprocket, but failures still occur on later 5th gens — the redesign reduced the risk, it did not eliminate the design. The 2020+ 6th gen went back to an external pump, so this note covers 2011–2019 only.
If a shop quotes the pump job, ask whether the price includes the timing chain, guides, and tensioners — and ask them to save the old parts. Owners who had old parts saved could verify the bearing failure with their own eyes.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 3,281 complaints for the 2011–2019 Ford Explorer. 2016 was the worst year (2454 complaints). Most-reported areas: steering, structure, unknown or other.
16V183000 (31/03/2016) — ENGINE AND ENGINE COOLING:ENGINE Ford Motor Company (Ford) is recalling certain model year 2015-2016 Lincoln MKC vehicles manufactured November 25, 2013, to January 25, 2016, and 2016 Ford Explorer vehicles manufactured October 20, 2014, to January 28, 2016. The affected vehicles are equipped with…
17V767000 (29/11/2017) — SEATS Ford Motor Company (Ford) is recalling certain 2016 F-150 and Explorer vehicles. Loose power seat adjuster pivot bolts may cause the front seat cushions to detach and not properly restrain the seat occupant in the event of a crash.
14V286000 (29/05/2014) — STEERING:ELECTRIC POWER ASSIST SYSTEM Ford Motor Company (Ford) is recalling certain model year 2011-2013 Ford Explorer vehicles manufactured May 17, 2010, through February 28, 2012. The affected vehicles may experience an intermittent connection in the electric power steering gear, which can cause a loss…
15V605000 (28/09/2015) — FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:MOUNTING Ford Motor Company (Ford) is recalling certain model year 2015 Ford Taurus, Lincoln MKS, and 2016 Ford Explorer vehicles manufactured on July 24, 2015. During vehicle production, the fuel tank attachment bolts may not have been properly tightened. As a…
17E048000 (28/08/2017) — WHEELS:HUB Ford Motor Company (Ford) is recalling certain Wheel Hub Bearing assemblies, part number HB5Z-1104-C, incorrectly listed as being for installation on the rear axles of 2011-2017 Ford Explorer 4X2 vehicles. These bearings assemblies were manufactured without a self retention feature…
16V475000 (28/06/2016) — SEATS:FRONT ASSEMBLY:RECLINER Ford Motor Company (Ford) is recalling certain model year 2016 Ford Explorer and F-150 vehicles equipped with a manual recline driver's seat. The seat back frame may have insufficient welds which may not meet the requirements of Federal Motor Vehicle…
19 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
NHTSA has published 413 manufacturer communications (service bulletins, dealer notices) covering the 2011–2019 Ford Explorer.
Most cited systems: Electrical System (129), Equipment (110), Engine And Engine Cooling (55), Power Train (55), Engine (32).
25N17 (Mar 2026) — Back Over Prevention, Lane Departure, Unknown Or Other
NHTSA also opened 8 defect investigations covering these years.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.