C0050

C0050 on a 2011–2019 Ford Explorer: Right Rear Wheel Speed Sensor Circuit Malfunction

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: C0050 on a 2009–2016 Audi A4 · 2012–2018 Audi A6 · 2006–2011 BMW 3 Series · 2012–2018 BMW 3 Series · 2010–2017 Chevrolet Equinox · 2014–2019 Chevrolet Silverado 1500
Show all 18 vehicles with this code

2011–2019 Ford Explorer · 2014–2018 GMC Sierra 1500 · 2016–2021 Honda Civic · 2011–2019 Hyundai Sonata · 2011–2021 Jeep Grand Cherokee · 2007–2018 Jeep Wrangler · 2013–2018 Nissan Altima · 2010–2019 Subaru Outback · 2019–2026 Toyota Corolla · 2019–2024 Toyota RAV4 · 2005–2023 Toyota Tacoma · 2011–2018 Volkswagen Jetta

DIY difficulty 3/5

Your car's ABS computer found an electrical problem in the right rear wheel speed sensor wiring. Your regular brakes work fine, but ABS and traction control may be disabled.

Key facts

☑ Before you buy parts — check these first:
On your 2011–2019 Ford Explorer (3.5L V6) — Front brake pads and rotors: Owner-verified
Remove the wheel (19mm lug nuts). Unbolt the two caliper slide-pin bolts (17mm socket/wrench) and hang the dual-piston caliper from the strut — never let it hang by the flex hose. Remove the two 18mm caliper bracket bolts from the knuckle, lift off the bracket, then remove the T40 Torx rotor hold-down screw; knock the rusted rotor off the hub (a lug nut threaded on hand-tight keeps it from flying). Clean the hub face, install the new rotor, then reinstall the bracket with fresh medium-strength threadlocker. Compress the dual pistons with the bleeder screw cracked open so dirty fluid bleeds out instead of being pushed back into the ABS module.
Do this test first: 1. Clear the code, drive above about 15 mph, and re-scan. Only spend money if the code comes back.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for C0050 on the 2011–2019 Ford Explorer — but the community-sourced Front brake pads and rotors note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: 1A Auto: How to Replace Front Brakes 2011–2019 Ford Explorer — full transcript with torque specs (done on 2018 Explorer Sport 3.5L) · 2014 Ford Explorer Owner's Guide, p. 385 — wheel lug nut torque 100 ft-lb (135 Nm) · ExplorerForum: tire rotation thread — owners confirm 100 ft-lbs lug torque on this generation

Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to C0050: 18 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. 1. Clear the code, drive above about 15 mph, and re-scan. Only spend money if the code comes back.
  2. 2. Watch the right rear wheel speed in ABS live data at low speed. A dead, jumpy, or mismatched reading confirms the problem corner. Tests: failed wheel speed sensor (most common)
  3. 3. Unplug the right rear sensor and inspect the connector for corrosion, moisture, or bent pins. Tests: corroded or loose sensor connector
  4. 4. Trace the sensor harness along the wheel-arch flex point and look for chafing, cracks, or breaks. Tests: wiring break or chafing at the wheel-arch flex point
  5. 5. Inspect the tone ring for cracked or missing teeth while the wheel is off.
  6. 6. If the wiring and tone ring check out, replace the right rear wheel speed sensor — it is the most common fix.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2011–2019 Ford Explorer: Front brake pads and rotors — test first, then buy for this job.

Expensive fork: Brake caliper — if a wheel drags or overheats after fresh pads and rotors. The price range below is a national planning range for C0050 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $180
Labor$90 – $250

A wheel speed sensor replacement, often $150-$350 installed at an independent shop. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0050 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Sensor and harness work with basic hand tools; seized sensors and corroded connectors are the usual fights.

Watch this repair on YouTube

Parts & tools

ABS / wheel-speed toolkit — what the job actually takes

Torque specs: Wheel-speed sensor bolts: typically 8–12 Nm. (Caliper bracket bolts are far tighter — 90–140 Nm — don’t confuse them.)

Pro tip: Inspect the tone ring/reluctor for cracks and debris first — the sensor itself is often innocent.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →