Diagnose soonLimp mode protects the engine. Avoid hard acceleration until diagnosed.
Your turbo isn't making full boost - the car feels gutless, especially uphill. Usually a torn diverter valve or a boost leak, not a dead turbo.
Model notes: Pressure-test or smoke-test the charge piping. Log requested vs actual boost - actual tracking below requested under load confirms it before buying parts.
Key facts
P0299 means turbocharger/supercharger underboost condition. Your turbo isn't making full boost - the car feels gutless, especially uphill. Usually a torn diverter valve or a boost leak, not a dead turbo. WrenchFair's published fair-price range for this repair is $60–$300 parts and $100–$300 labor at independent shops.
WrenchFair rates P0299 a 3-of-5 DIY difficulty (“DV is easy; finding piping leaks takes patience.”) with a “Diagnose soon” driveability rating: Limp mode protects the engine. Avoid hard acceleration until diagnosed. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2008–2024 Ram 2500 (6.7L Cummins I6 diesel) — 6.7L Cummins cracked exhaust manifold (tick, soot, underboost):Owner-verified
Big driveway job — the manifold lives behind the turbo with heat-seized studs. Soak every fastener in penetrant for days beforehand, plan on replacing gaskets and studs, and budget a full weekend.
Do this test first: Pressure-test or smoke-test the charge piping
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0299 on the 2008–2024 Ram 2500 — but the community-sourced 6.7L Cummins cracked exhaust manifold (tick, soot, underboost) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Exhaust manifold bolts/studs: verify — Sequence and spec matter on a hot casting — confirm the factory figure for your year; do not guess.
Turbo flange hardware: verify — New studs/nuts with anti-seize; the old hardware is usually heat-welded in place.
Tips
The one-piece factory exhaust manifold on the 6.7 Cummins is a known cracking part from repeated heat cycles — the entire two-piece aftermarket exists to fix exactly this failure mode (ATS, BD, and Diesel Power Source all build 2-piece slip-joint manifolds because the stock casting cracks).
Symptoms: an RPM-synchronous ticking that is loudest on cold startup, soot staining around the manifold or turbo flange, a faint exhaust whistle, and a slow loss of power or fuel mileage. One owner chased the tick through several dealers for 8+ months before a crack finally opened enough to be found — a slight leak gets worse with time.
Do not confuse this with HEMI tick: this note is diesel-only. The 6.4L HEMI broken exhaust-manifold-bolt problem is a separate note for the gas trucks.
The community-standard fix is a two-piece expansion-joint manifold (ATS 2049272326 for 2007.5-2018, BD 1046069 kit for 2019-2024), which lets the casting expand and contract instead of cracking. Do not reuse the OEM gaskets — get the full hardware and MLS gasket kit. Lay a straightedge across the flange; warped flanges need to go too.
A cracked manifold leaks exhaust before the turbo, so the truck can set P0299 (turbo underboost). If you already have P0299 with a tick, check the manifold for soot before condemning the turbo or the VGT actuator — those are separate notes.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
loss of power
limp mode under load
whooshing noise
check engine light
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Torn diverter/blow-off valve diaphragm 11 owner notes link this repair to P0299
Boost leak (intercooler piping, clamps) 3 owner notes link this repair to P0299
Sticking wastegate or failed boost control solenoid 11 owner notes link this repair to P0299
Failing turbocharger (last resort) 11 owner notes link this repair to P0299
Owner notes linked to P0299: 15 across 3 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Pressure-test or smoke-test the charge piping
Remove and inspect the diverter valve diaphragm Tests: Torn diverter/blow-off valve diaphragm
Log requested vs actual boost under load
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2008–2024 Ram 2500: 6.7L Cummins cracked exhaust manifold (tick, soot, underboost) — test first, then buy for this job.
The price range below is a national planning range for P0299 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$60 – $300
Labor$100 – $300
Diverter valve or hose fix is typical; turbo replacement is far more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0299 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — DV is easy; finding piping leaks takes patience.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →