Community-sourced DIY repair guides for the 2008–2024 Ram 2500, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Pan-drop driveway job. The valve body comes out once the pan and filters are off; keep bolts organized and have fresh ATF+4 and both filters on hand before you start.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Valve body to case bolts: verify — Small 8mm-headed bolts; factory torque is an inch-pound value — confirm the exact figure for your year in service info rather than guessing.
Transmission pan bolts: verify — Snug in a crisscross pattern; overtightening warps the pan and guarantees a leak.
Tips
The community consensus on the RFE family (68RFE behind the Cummins, 66RFE behind the 6.4 HEMI) is blunt: the transmission itself is stout, but the stock valve body wears out. The channel-plate-to-valve-body seal is a bare metal separator plate with no gasket material, so it cross-leaks and drags clutches that should not be engaged; the accumulator pistons rock in their bores, scuff them, and leak past their seals.
Symptoms are shift-quality problems that get worse with heat and miles: 2-3 shift flare, harsh or late downshifts, delayed engagement, and odd shift timing. As one RamForum veteran puts it, with miles it is only a matter of time before the valve body leaks — nature of the beast.
Clean-before-you-spend: scan for codes first. Solenoid packs are not the usual failure here — owners report they rarely go bad compared with the valve body itself, which is known for cross-leaks and seepage past the accumulator pistons from poor casting/machining quality. A failing solenoid pack usually throws a code; worn accumulator bores often do not.
The owner-standard fix is a pan-drop valve-body refresh: billet channel plate with proper separator gaskets, billet aluminum accumulator pistons (e.g. Sonnax 44894-01K single or 44894-01MK 5-piece kit, whose relocated scarf-cut seal salvages moderately worn bores and whose dual guide seals stop the rocking/scuffing), and fresh filters and ATF+4. DNJ and Revmax also make the channel plate. One owner reported a remanufactured valve body around $300 plus a $100 core charge as an alternative to rebuilding your own.
This is a different campaign from the 2019-2023 68RFE valve-body fire recall (W03 / 20V-043) — that is a separate recall note. This note covers wear-driven shift problems across the whole 68RFE/66RFE run.
Big driveway job — the manifold lives behind the turbo with heat-seized studs. Soak every fastener in penetrant for days beforehand, plan on replacing gaskets and studs, and budget a full weekend.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Exhaust manifold bolts/studs: verify — Sequence and spec matter on a hot casting — confirm the factory figure for your year; do not guess.
Turbo flange hardware: verify — New studs/nuts with anti-seize; the old hardware is usually heat-welded in place.
Tips
The one-piece factory exhaust manifold on the 6.7 Cummins is a known cracking part from repeated heat cycles — the entire two-piece aftermarket exists to fix exactly this failure mode (ATS, BD, and Diesel Power Source all build 2-piece slip-joint manifolds because the stock casting cracks).
Symptoms: an RPM-synchronous ticking that is loudest on cold startup, soot staining around the manifold or turbo flange, a faint exhaust whistle, and a slow loss of power or fuel mileage. One owner chased the tick through several dealers for 8+ months before a crack finally opened enough to be found — a slight leak gets worse with time.
Do not confuse this with HEMI tick: this note is diesel-only. The 6.4L HEMI broken exhaust-manifold-bolt problem is a separate note for the gas trucks.
The community-standard fix is a two-piece expansion-joint manifold (ATS 2049272326 for 2007.5-2018, BD 1046069 kit for 2019-2024), which lets the casting expand and contract instead of cracking. Do not reuse the OEM gaskets — get the full hardware and MLS gasket kit. Lay a straightedge across the flange; warped flanges need to go too.
A cracked manifold leaks exhaust before the turbo, so the truck can set P0299 (turbo underboost). If you already have P0299 with a tick, check the manifold for soot before condemning the turbo or the VGT actuator — those are separate notes.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 420 complaints for the 2008–2024 Ram 2500. 2016 was the worst year (258 complaints). Most-reported areas: engine, power train, electrical system.
23V799000 (28/11/2023) — STEERING:STEERING CONTROL MODULE Chrysler (FCA US, LLC) is recalling certain 2023 Ram 1500 Classic, Ram 3500 Classic, 3500 Cab Chassis, 2023-2024 Ram 2500, 4500/5500 Cab Chassis, and Ram 3500 vehicles. The steering column control module may cause the high beams to activate when…
23V654000 (28/09/2023) — BACK OVER PREVENTION:DISPLAY FUNCTION Chrysler (FCA US, LLC) is recalling certain 2022-2023 Ram 1500, Ram 3500 Cab Chassis with GVWR less than 10,000 lbs., and 2022-2024 Ram 2500 vehicles. The radio software may prevent the rearview image from displaying. As such, these vehicles fail…
18V486000 (27/07/2018) — STRUCTURE:BODY:TAILGATE Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may…
22V035000 (27/01/2022) — VISIBILITY:WINDSHIELD WIPER/WASHER:LINKAGES Chrysler (FCA US, LLC) is recalling certain 2019-2020 Ram 2500 and Ram 3500 vehicles, Ram 3500 Cab Chassis, 4500 Cab Chassis, 5500 Cab Chassis and 3500 Cab Chassis with a gross vehicle weight rating (GVWR) of less than 10,000 lbs…
19V021000 (25/01/2019) — STEERING:LINKAGES:DRAG:LINK:CONNECTION Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
20V043000 (24/01/2020) — POWER TRAIN:AUTOMATIC TRANSMISSION Chrysler (FCA US LLC) is recalling certain 2019-2020 Ram 2500 and 3500 Pickup vehicles equipped with six-speed automatic (68RFE) transmissions. A build up of pressure and heat inside the transmission may result in a transmission fluid leak from the dipstick…
28 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2008–2024 Ram 2500 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.