Diagnose soonErratic throttle is a safety concern - diagnose promptly.
Your throttle's backup sensor is reading wrong - it's drifting or has a dead spot. Expect jumpy throttle response or limp mode.
Key facts
P0221 means throttle/pedal position sensor 'B' range/performance. Your throttle's backup sensor is reading wrong - it's drifting or has a dead spot. Expect jumpy throttle response or limp mode. WrenchFair's published fair-price range for this repair is $100–$400 parts and $80–$250 labor at independent shops.
WrenchFair rates P0221 a 2-of-5 DIY difficulty (“Sweep-test both sensors on a scan tool - a dead spot shows as a jump.”) with a “Diagnose soon” driveability rating: Erratic throttle is a safety concern - diagnose promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 454 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Engine And Engine Cooling) — see the latest ones
On your 2017–2022 Honda CR-V (1.5L turbo (L15BE)) — Throttle body cleaning:Owner-verified
The 1.5T uses a drive-by-wire ETCS throttle body on the intake manifold. The factory manual says to remove the throttle body to clean it — check the air cleaner for damage first, then pull the body and clean carbon from the throttle valve and bore with a paper towel soaked in throttle plate and induction cleaner. Do NOT spray cleaner directly on the throttle body, do NOT clean the bearing area of the throttle shaft (it has a molybdenum coating), and never stick fingers in the throttle body with the ignition on. Reinstall, reset the PCM, and run the PCM idle learn procedure (below). For diagnosis, the manual's carbon-accumulation check: with HDS at idle, REL TP SENSOR should read below 2.46 degrees — if higher, clean the throttle body; there's also a TP position check under the ETCS test menu.
Do this test first: Clean the throttle body thoroughly
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0221 on the 2017–2022 Honda CR-V — but the community-sourced Throttle body cleaning note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Throttle body mounting bolts: verify — Confirm against factory service info before torquing.
Tips
PCM idle learn is REQUIRED after cleaning or replacing the throttle body (factory procedure): all electrical items off; reset the PCM with HDS; ignition ON 2 seconds; start engine and hold 3,000 rpm no-load (Park/neutral) until the radiator fan comes on or ECT reaches 194 F; then idle ~5 minutes with the throttle fully closed (exclude fan run time); confirm completion on the HDS data list. No-HDS workaround from Honda owners: disconnect the battery 10-15 minutes to force the PCM reset, then run with all loads off until the fans cycle twice.
Target idle after learn: 650 +/- 50 rpm no load (Park/neutral), 700 +/- 50 rpm with high electrical load.
Skipping the relearn causes the classic symptom: high/surging idle (1,200-1,500 rpm) and jerky throttle response after cleaning.
Use Honda genuine throttle plate and induction cleaner per the manual; carb cleaner substitutes can damage the coating.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Typical time: “PCM idle learn is REQUIRED after cleaning or replacing the throttle body (factory procedure): all electrical items off; reset the PCM with HDS; ignition ON 2 seconds; start engine and hold 3,000 rpm no-load…” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
erratic throttle response
hesitation
possible limp mode
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Worn throttle position sensor 'B' with a dead spot (most common) 4 owner notes link this repair to P0221
Carbon-fouled throttle plate sticking 4 owner notes link this repair to P0221
Drifting sensor
Owner notes linked to P0221: 5 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Clean the throttle body thoroughly Tests: Worn throttle position sensor 'B' with a dead spot (most common)
Slowly sweep the throttle and watch sensors 'A' and 'B' for dropouts or jumps Tests: Worn throttle position sensor 'B' with a dead spot (most common)
Check that the throttle plate moves freely Tests: Carbon-fouled throttle plate sticking
Replace the throttle body if sensor 'B' has a dead spot Tests: Worn throttle position sensor 'B' with a dead spot (most common)
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2017–2022 Honda CR-V: Throttle body cleaning — test first, then buy for this job.
The price range below is a national planning range for P0221 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $400
Labor$80 – $250
Throttle body cleaning or replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0221 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Sweep-test both sensors on a scan tool - a dead spot shows as a jump.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →