Community-sourced DIY repair guides for the 2017–2022 Honda CR-V, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Pop the plastic engine cover off first (it lifts free with the coil area exposed), then disconnect each coil's harness connector and remove the 10mm coil bolts. The coils pull straight out of deep wells; use a thin-wall 14mm spark plug socket with an extension to reach the M12-thread plugs. Straightforward job on the transverse inline-4 — the only real pain point is debris dropping into the open plug wells while you work.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Torque specs
Spark plugs: 22 Nm (16 lb-ft) — Honda's factory 1.5L torque chart lists spark plugs at 22 N·m (16 lbf·ft). Some walkthroughs quote 13 ft-lbs (older-gen figure) — use the factory 22 N·m for the 1.5T. Confirm against factory service info before torquing.
Ignition coil bolts (10mm): verify — Confirm against factory service info for this engine before torquing.
Tips
Use the OEM plug: NGK 95660 (laser iridium) — confirmed in 2017–2022 CR-V 1.5T walkthroughs. Do NOT use Honda 9807B-5617W / NGK IZFR6K11: that plug fits the older 2.4L CR-V (2002–2009), not the 1.5T.
Honda's interval is 100k miles on the iridium plugs; the 2017 CR-V 1.5T owner's thread shows originals looking fine at 95k, so don't change early.
Hand-thread plugs into the aluminum head before any wrench to avoid cross-threading; thread damage is the #1 DIY failure on this job.
Buy NGK plugs from a dealer or reputable store — a CR-V 1.5T owner's thread warns of counterfeit NGK plugs on Amazon (one owner got burned with fakes).
The 1.5T runs a primary wideband LAF (air/fuel ratio) sensor in the downpipe before the catalytic converter (Honda P/N 36531-5K8-004 fits all 2017–2022 CR-V 1.5T) and a secondary heated O2 sensor after the cat. Unplug the harness connector (wiring routes toward the firewall), then break the sensor loose with a 22mm slotted O2 sensor socket. The exhaust-side corrosion is the pain point: soak the bung with penetrating oil the day before, and right before the job run the engine about one minute so the thin exhaust pipe expands faster than the sensor — an owner-reported trick that freed a stuck CR-V sensor.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
Torque specs
O2 sensors: verify — No Honda-published torque spec was sourced for the 1.5T LAF/AFR sensor. Confirm against factory service info before torquing; tighten snug and do not overtighten.
Tips
The upstream is a heated 5-wire wideband A/F sensor — much more expensive than the downstream narrowband; don't swap in a cheap narrowband substitute.
Check for exhaust leaks at or before the sensors first: leaks skew readings and trigger false codes, per the 2017–2019 CR-V service-manual-based guide.
Inspect sensor wiring and connectors for heat/road-grime damage during major services; intermittent faults are common there.
Confirm with a scanner before buying: P0134/P0135 point to the A/F sensor circuit/heater, P0138 to the rear O2 high voltage, P0420 to catalyst efficiency.
On the 1.5T the thermostat housing (water outlet) sits low on the engine block where the lower radiator hose connects — follow that hose back from the radiator. Drain the radiator through the bottom petcock first, then remove or shift the air intake ducting aside for working room. Unclamp the lower hose at the housing, unbolt the two/three 10mm housing bolts, and keep a catch pan under the housing — the block holds residual coolant that spills when the housing comes off. Tight low-bay access is the pain point; intake-duct removal makes it manageable.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
Thermostat housing bolts (10mm): 10 N·m (88 in-lb) — Per the 1.5T CR-V guide (Repco): 'Honda four-cylinder housing bolts are typically around 10 N·m'. Confirm in factory service info before torquing.
Tips
Buy the OEM thermostat SET 06193-59B-306 (thermostat + gasket, fits 2017–2021 Civic/CR-V 1.5T) rather than a bare thermostat — the gasket/O-ring should always be replaced.
Refill only with Honda Type 2 blue premixed long-life coolant; don't mix coolant types — if unsure what's in there, drain and refill fully.
Bleed properly: radiator cap off, heater on full hot, run until the radiator fans cycle and bubbles stop, then re-check the reservoir level after a drive.
Do not overtighten the small housing bolts — over-torquing cracks plastic flanges or strips aluminum threads; a small torque wrench is the right tool.
Front brake pads & rotors Owner-verified(1.5L turbo (L15BE))
Remove the front wheel. Unbolt the caliper from its bracket via the two slide-pin bolts on the back of the caliper and hang the caliper from the strut/coil spring with wire — never let it dangle by the brake hose (Honda service-info procedure). For rotor replacement, remove the two large caliper bracket bolts that thread into the knuckle (tight from the factory; use a breaker bar). The rotor is retained by Honda's 6mm Phillips-head set screws. The front caliper is a single-piston floating design: compress the piston straight back into the bore with a C-clamp or piston tool before fitting it over the new pads. Pump the brake pedal several times until it firms up before driving.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Typical time: “Bed the new pads/rotors: 5 moderate-to-aggressive stops from 40 to 10 mph in rapid succession without fully stopping, then 5 moderate stops from 35 to 5 mph, then ~5 minutes of moderate-speed driving without stopping to…” — as written in the note. First-timers often take twice this.
Torque specs
Lug nuts: 80 lbf·ft (108 N·m) — Owner's-manual spec; tighten in a star pattern and recheck after driving.
Caliper bracket bolts: verify — Confirm against factory service info for this engine.
Caliper slide-pin bolts: verify — Confirm against factory service info for this engine.
Tips
Honda's infamous rotor set screws seize in the hub: attack them first with an impact screwdriver and a No. 3 Phillips bit — do not try a regular screwdriver or you will round the heads. If the screw heads are already stripped, drill the heads off; the screw is not needed for operation.
If the rotor is rust-welded to the hub, Honda's own procedure is to thread two 8 x 1.25mm bolts into the threaded holes in the rotor hat and turn each 90 degrees at a time to push the rotor off evenly.
The two large caliper bracket bolts come coated with thread locker from the factory — expect to need a breaker bar or impact to break them loose, and re-apply the same type of thread locker when reinstalling.
Clean and re-grease the slide pins with silicone-based brake grease; Honda specifies Molykote M-77 assembly paste on the pad backing plates and shims. Keep all grease off the friction surfaces.
Bed the new pads/rotors: 5 moderate-to-aggressive stops from 40 to 10 mph in rapid succession without fully stopping, then 5 moderate stops from 35 to 5 mph, then ~5 minutes of moderate-speed driving without stopping to let the brakes cool and cure (PowerStop break-in procedure).
Pump the brake pedal several times until it is firm before lowering the car — the pistons were pushed back and must re-seat against the new pads.
Battery is under the hood, driver's side. With the engine off: loosen and remove the black negative cable first, then the red positive cable; remove the hold-down clamp/bracket with a wrench or ratchet; lift the battery straight out of the tray (it is heavy). Install in reverse: set the battery in the tray, refit the hold-down, connect positive first, then negative last. 2017–2019 1.5T models use a Group 51R flooded lead-acid battery (no vent hose to reroute); 2020+ models with auto idle stop switched to the larger Group 4A/H5 battery.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Typical time: “Idle relearn after reconnecting: turn all electrical loads OFF (A/C, lights, audio), hold the engine at 3,000 rpm until the radiator fan cycles on, release the throttle and let it idle untouched for 5 minutes (Honda…” — as written in the note. First-timers often take twice this.
Tips
Idle relearn after reconnecting: turn all electrical loads OFF (A/C, lights, audio), hold the engine at 3,000 rpm until the radiator fan cycles on, release the throttle and let it idle untouched for 5 minutes (Honda idle-relearn procedure). Idle may hunt or sit high until this completes.
Power-window auto up/down is lost after a battery swap. Reset the driver's window: ignition ON, run the window fully down and hold the switch 2 seconds, then fully up and hold 2 seconds (Honda power-window control-unit reset procedure).
No manual radio-code entry is needed on 2017+ Hondas: the audio unit automatically retrieves its anti-theft unlock code from the body control module over the CAN bus.
If a VSA/steering warning lights up after reconnect, drive in a straight line at 10 mph or more for about 10 seconds to complete the steering-angle neutral-position learn (2018 CR-V 1.5T Honda procedure).
51R batteries are sold with terminals toward the front or the rear — match the terminal orientation of the old battery before buying, or the cables will not reach.
Use a memory saver on the OBD-II port if you want to skip all the relearn procedures above.
No tank drop needed: fold the left side rear seat forward and pull back the carpet to expose the fuel tank unit access panel in the floor (per the factory manual). Relieve fuel pressure first per Honda's procedure — disable the pump, then disconnect the fuel tube/quick-connect fitting in the engine compartment — and disconnect the battery. The pump module comes out through the panel; the recall TSB procedure specifies a new O-ring (do not coat it with oil), aligning the tank-unit tab, installing the cam lock ring by hand, then tightening it clockwise with a fuel sender wrench and confirming the ring is not 'floating.' After reassembly, cycle the ignition ON (engine off) two to three times to prime the lines and check for leaks. Note: the 1.5T also has a cam-driven high-pressure pump on the engine — this job is the in-tank module only.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
Fuel tank unit cam lock ring: verify — Confirm against factory service info before torquing.
Tips
Check the fuel pump impeller recall first: 2018-2020 CR-Vs are covered by NHTSA 23V-858 (Honda KGC/KGD), an expansion of 21V-215/20V-314 — dealers replace the pump module free; check your VIN on NHTSA or Honda's recall site before buying parts.
Pump runs for ~2 seconds at key-on (listen at the filler neck with the cap off) — a quick no-start diagnosis straight from the factory troubleshooting tree.
Use a new O-ring and cam lock ring; do not oil the O-ring, and seat the lock ring tabs into the positioning edge by hand before tightening so it doesn't float.
Do not bend the fuel level sensor arm during removal — it can cause inaccurate gauge readings.
Throttle body cleaning Owner-verified(1.5L turbo (L15BE))
The 1.5T uses a drive-by-wire ETCS throttle body on the intake manifold. The factory manual says to remove the throttle body to clean it — check the air cleaner for damage first, then pull the body and clean carbon from the throttle valve and bore with a paper towel soaked in throttle plate and induction cleaner. Do NOT spray cleaner directly on the throttle body, do NOT clean the bearing area of the throttle shaft (it has a molybdenum coating), and never stick fingers in the throttle body with the ignition on. Reinstall, reset the PCM, and run the PCM idle learn procedure (below). For diagnosis, the manual's carbon-accumulation check: with HDS at idle, REL TP SENSOR should read below 2.46 degrees — if higher, clean the throttle body; there's also a TP position check under the ETCS test menu.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Typical time: “PCM idle learn is REQUIRED after cleaning or replacing the throttle body (factory procedure): all electrical items off; reset the PCM with HDS; ignition ON 2 seconds; start engine and hold 3,000 rpm no-load…” — as written in the note. First-timers often take twice this.
Torque specs
Throttle body mounting bolts: verify — Confirm against factory service info before torquing.
Tips
PCM idle learn is REQUIRED after cleaning or replacing the throttle body (factory procedure): all electrical items off; reset the PCM with HDS; ignition ON 2 seconds; start engine and hold 3,000 rpm no-load (Park/neutral) until the radiator fan comes on or ECT reaches 194 F; then idle ~5 minutes with the throttle fully closed (exclude fan run time); confirm completion on the HDS data list. No-HDS workaround from Honda owners: disconnect the battery 10-15 minutes to force the PCM reset, then run with all loads off until the fans cycle twice.
Target idle after learn: 650 +/- 50 rpm no load (Park/neutral), 700 +/- 50 rpm with high electrical load.
Skipping the relearn causes the classic symptom: high/surging idle (1,200-1,500 rpm) and jerky throttle response after cleaning.
Use Honda genuine throttle plate and induction cleaner per the manual; carb cleaner substitutes can damage the coating.
CVT fluid service Owner-verified(1.5L turbo (L15BE))
The 1.5T uses a CVT — there is NO dipstick. Service is a drain-and-fill: remove the drain plug, drain (~4 quarts measured out on an '18 CR-V by owners), refill through the fill hole with Honda HCF-2 CVT fluid ONLY. Level is set via the 12mm check bolt above the drain plug: vehicle level, engine run, shift through all positions (~3 seconds each), back to Park, engine off, then remove the check bolt — a slow drip from the hole means the level is correct; no flow means add more, pouring means let it drain down. Use new crush washers on both plugs. A single drain-and-fill only replaces about one-third of the fluid, so owners and Honda's own service approach use repeated drain-and-fills (Honda bulletin 16-061 defines 'flushing' as drain-and-fill with a drive cycle three times) — never use aftermarket flush equipment. Two filters exist and ARE serviceable on deeper services: the CVT warmer filter (25450-P4V-013, with warmer O-rings 25565-5LJ-A01 / 25564-5LJ-A01 / 91305-PN4-003) and the internal pan filter (25420-5LJ-003, requires dropping the pan with new gasket 21814-RJ2-003); check-bolt washer is 90471-59C-000. Owners typically do filters on the second or third fluid service, not every drain.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
CVT drain plug: verify — Confirm against factory service info before torquing.
CVT check bolt: verify — Confirm against factory service info before torquing.
Tips
Honda HCF-2 ONLY — owners report slipping/shudder issues with substitute CVT fluids; switching back to Honda fluid fixed them.
The check bolt washer (90471-59C-000) is a separate part number from the drain plug washer — buy both before starting.
Owner oil analysis on an '18 CR-V shows HCF-2 shearing down within ~25-30k miles; forum owners do a drain-and-fill every 25-30k miles as cheap insurance.
Resetting the maintenance minder after service is normal; a shudder that clears after fresh Honda fluid often just needed the service.
1.5T oil dilution (fuel in oil) Owner-verified(1.5L turbo (L15B7))
No teardown — this is a management-and-maintenance note. Check the dipstick with the engine cold: smell the oil and note whether the level sits above the full mark. The dealer software update is a service-visit item, not DIY.
Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).
Typical time: “If your trips are all short, give it a 10–15 minute highway run regularly so the engine fully warms and evaporates fuel out of the oil.” — as written in the note. First-timers often take twice this.
Torque specs
Drain plug / oil filter: verify — No torque-critical fastener beyond standard oil-change items; follow the owner's manual drain-plug and filter specs. Do not overtighten the aluminum drain pan.
Tips
Diagnose it yourself first: on a cold engine, pull the dipstick — fuel-smelling oil plus a level that has crept above the full mark is the signature. Cold-climate short trips make it worse; the CR-V was the model Honda singled out for its free fix campaign.
Get Honda's Product Update done at the dealer if it applies to your VIN — it is free. The update reflashes the engine and CVT control software (and replaces the A/C control unit on some vehicles) so the engine warms up faster, and Honda rolled it out to cold-weather states first (ME, MN, ND, SD, WI, then 21 states). Call any dealer with your VIN to check whether it has been applied.
Shorten your oil-change interval well below the Maintenance Minder on affected cars — the owner consensus is 3,000–5,000 miles, not the 7,500+ the minder may suggest, because diluted oil is thinner oil. Several owners with oil-analysis reports run 0W-30 instead of the spec 0W-20 in winter so the diluted oil lands closer to a 20-weight.
Avoid moving the car for 20 seconds from a cold start and shutting it off — that is the worst possible drive cycle for dilution. If your trips are all short, give it a 10–15 minute highway run regularly so the engine fully warms and evaporates fuel out of the oil.
Be honest about the limits: owners widely report the software update helps but does not eliminate dilution in cold climates, and dealers have told some owners the contamination is 'normal' — document every visit with a repair invoice. Persistent cases (rapid level rise, strong fuel smell at 3k miles) belong back at the dealer in writing, especially inside the powertrain warranty.
AC compressor shaft seal leak (TSB A23-040 warranty) Owner-verified(1.5L turbo (L15B7), 2.4L K24W)
The compressor sits low on the front of the engine; the shaft seal is at its front face. The under-hood fuse box (AC relay) is reachable without tools. Refrigerant handling is shop-only — this note is about diagnosis, the free-warranty path, and avoiding a misdiagnosis.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
AC fittings / compressor bolts: verify — Refrigerant system is shop-only work; if a DIYer replaces hard parts, confirm all fastener torque against factory service info and have the system evacuated and charged professionally.
Tips
Check whether Honda's extended warranty covers you BEFORE paying for anything: TSB A23-040 extends the A/C compressor shaft-seal warranty from 3 years to 10 years with no mileage limit (NHTSA ID 10249629) because a refrigerant/oil regulation change made the seals leak. If your 2017–2022 CR-V's AC went warm, call the dealer with your VIN first — this is a free repair, not a $1,000+ shop bill.
Rule out the $10 fix first: owners name the A/C compressor relay in the under-hood fuse box as the first check when the AC quits. Swap it with an identical relay from the box and see if the clutch engages — no tools beyond a fingernail.
Know the dealer-misdiagnosis pattern owners report: on these CR-Vs the leak is often the high-pressure hose from the compressor (visibly contaminated with AC oil where it connects), not the compressor itself — but dealers have quoted full compressor replacements off a same-day dye test. A real dye test needs a week or two of driving before re-inspection; a same-day 'found the leak' is a red flag worth questioning.
If you are out of warranty and it really is the compressor, budget honestly: owners report roughly $1,000+ at an independent shop for compressor plus recharge, and a seized compressor can throw debris through the system (condenser, expansion valve) which multiplies the bill. Do not keep running the AC once it blows warm — a struggling compressor does more damage the longer it runs.
Rear differential fluid service (AWD groan on turns) Owner-verified(1.5L turbo (L15B7), 2.4L K24W)
Straightforward driveway job on a level surface: the rear differential sits ahead of the rear axle. Remove the fill plug FIRST (so you know you can refill), then the drain plug, drain, reinstall drain plug, and pump fresh Honda Dual Pump Fluid II (DPSF-II) in through the fill hole until it starts to dribble back out. A fluid pump or large syringe makes the fill painless; no lift strictly needed per owner reports.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Rear differential drain and fill plugs: verify — Confirm against factory service info before torquing; use new crush washers.
Tips
Learn the signature before spending anything: a low groan, moan, or shudder from the rear on tight low-speed turns (parking lots, U-turns) that appears around 30k miles. Owners and techs agree this is almost always tired rear-diff fluid, not a bad differential - a drain-and-fill usually silences it.
Follow the Maintenance Minder, not a fixed mileage: the rear-diff service is triggered by sub-code 6 (e.g. B-6). Honda's own literature notes the first change can come as early as ~15,000 miles (break-in material), then typically every 30,000-60,000 miles.
Use ONLY Honda Dual Pump Fluid II (DPSF-II). Owners and EricTheCarGuy are unanimous: there is no acceptable substitute, and wrong fluid can damage the clutch packs. Do not let a shop talk you into a universal fluid.
Remove the fill plug before the drain plug. This is the classic DIY trap - draining first and then discovering the fill plug is seized leaves you with an empty differential and no way to refill.
Reset the Maintenance Minder sub-code after the service so the car recalculates the next interval; check the receipt wording if a dealer does it.
1.5T head gasket failure (10yr/150k warranty extension) Factory-documented(1.5L turbo (L15B7))
No DIY teardown - this is a diagnose-and-claim note. A head gasket job is shop-only, but under Honda's extended coverage it is FREE at the dealer for qualifying vehicles: check your VIN with a dealer before authorizing any paid repair.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Tips
Know the signature: unexplained coolant loss with no visible leak, an overheating gauge, and cylinder misfires (often on cold starts) on a 1.5T with ~60,000+ miles. AutoGuide confirms Honda's TSB names these exact symptoms; coolant leaking into the combustion chambers is the mechanism.
Do NOT pay for a head gasket job before checking coverage: Honda's September 2026 TSB extends head gasket warranty to 10 years / 150,000 miles (from the original 5 years / 60,000) for 2017-2026 CR-Vs, and it is transferable to subsequent owners. It is a TSB, not a recall - it applies when your vehicle shows the symptoms.
Act on the grace period: Torque News reports owners of older models have until the end of May 2027 to claim under the extension. Call a dealer with your VIN now rather than waiting for the failure to strand you.
Know what the dealer is authorized to do: per AutoGuide, technicians replace the head gasket free, and if the leak already caused secondary damage they can replace the cylinder head or the complete short block. This is a ~$5,000+ repair out of warranty per Autoblog.
Failure is not guaranteed: Autoblog notes plenty of these engines run past 200,000 miles without issue, and class-action lawsuits in Canada and the US drove the extension. If you are buying used, ask for proof the TSB repair was done or a clean bill via VIN.
CVT judder/shudder at gentle acceleration (2017-2019) Owner-verified(1.5L turbo (L15B7))
The DIY part is the fluid service (same procedure as the CVT fluid service note): drain-and-fill with Honda HCF-2 ONLY through the fill hole, level set via the check bolt. The software reprogram requires a dealer visit (i-HDS); start-clutch replacement is shop-only.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
Learn the signature: a shudder or judder like driving over rumble strips during gentle acceleration between 15 and 50 km/h (~10-30 mph), most reported on 2017-2019 models per Motor Illustrated. TrueDelta owners report the same judder around 1,800 RPM.
Ask the dealer about the service bulletins first: Motor Illustrated reports Honda issued bulletins calling for a TCM/ECU software reprogram plus a CVT fluid flush with genuine Honda HCF-2 fluid. The software update is a dealer item - do not let anyone sell you a transmission for this.
Do a fresh HCF-2 drain-and-fill yourself before assuming the worst: owners report judder clearing after fresh Honda fluid (see the CVT fluid service note for the procedure). Use ONLY HCF-2 - substitute fluids are a known cause of CVT shudder on these.
Know the escalation path honestly: if software plus fresh fluid does not fix it, Motor Illustrated says Honda prescribes replacement of the launch (start) clutch; in severe cases owners end up needing a replacement CVT. Get a second quote before authorizing a $4,500+ transmission.
Do not 'flush' with machines or additives: the Honda bulletin procedure is a drain-and-fill sequence with HCF-2, and owners warn that aftermarket fluids or flush machines make these CVTs worse, not better.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
DIY-friendliness scorecard
Score: 89/100 — DIY-friendly
Special tools mentioned in the notes (4, −16): spark plug socket, O2 sensor socket, torque wrench, camshaft locking tools.
Documented dealer-only steps (0, −0): none documented in the notes — that does not mean none exist.
How this is scored (mechanical, no opinion): start at 100; −4 per distinct special tool mentioned in the notes (max −28); −15 per documented dealer-only step (max −30); note-volume band: 15+ notes +10, 8–14 +5, 4–7 +0. Bands: 85+ DIY-friendly · 65–84 DIY with care · 40–64 Experienced DIY only · below 40 Think twice. Pilot rubric — flagged for Robbie’s eyeball before any scale-up.
NHTSA recorded 353 complaints for the 2017–2022 Honda CR-V. 2020 was the worst year (353 complaints). Most-reported areas: forward collision avoidance, air bags, electrical system.
23V524000 (27/07/2023) — EQUIPMENT:OTHER:LABELS Honda (American Honda Motor Co.) is recalling certain 2017, 2020, and 2022 CR-V vehicles. The certification label on the driver's side door states incorrect Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR), and tire size information. As such…
22V380000 (26/05/2022) — FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY Honda (American Honda Motor Co.) is recalling certain 2020 CR-V vehicles. The clip for the absorber inside the fuel tank was not secured properly and may detach, which can cause an inaccurate fuel gauge reading.
23V158000 (09/03/2023) — SEAT BELTS:FRONT:BUCKLE ASSEMBLY Honda (American Honda Motor Co.) is recalling certain 2017-2020 CR-V, 2018-2019 Accord and Accord Hybrid, 2018-2020 Odyssey, 2019 Insight, and 2019-2020 Acura RDX vehicles. A manufacturing issue with the front seat belts may cause the seat belt buckle channel to…
19V865000 (05/12/2019) — STRUCTURE:FRAME AND MEMBERS Honda (American Honda Motor Co.) is recalling certain 2019-2020 CR-V vehicles. The rear subframe bolts were improperly manufactured and may loosen, allowing the rear subframe to separate.
7 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
NHTSA has published 454 manufacturer communications (service bulletins, dealer notices) covering the 2017–2022 Honda CR-V.
Most cited systems: Electrical System (122), Equipment (70), Engine And Engine Cooling (68), Fuel System, Gasoline (57), Visibility (57).
ONL6UV09092026 (Sep 2026) — Forward Collision Avoidance, Lane Departure — bulletin PDF on NHTSA →
NHTSA also opened 3 defect investigations covering these years.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.