Drive safeSafe to drive. Fix before any catalyst diagnosis.
Can I drive with P0138?
Can I drive with a P0138 code?
Yes. P0138 doesn't make your car unsafe to drive on its own. Safe to drive. Fix before any catalyst diagnosis. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.
How serious is P0138?
Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Safe to drive. Fix before any catalyst diagnosis.
Will P0138 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
The sensor behind your catalytic converter is stuck reading high. It's a sensor or wiring problem - not proof your catalytic converter is bad.
Model notes: Fix this before trusting any P0420 catalyst reading, since catalyst monitoring depends on this sensor.
Key facts
P0138 means o2 sensor circuit high voltage, bank 1 sensor 2. The sensor behind your catalytic converter is stuck reading high. It's a sensor or wiring problem - not proof your catalytic converter is bad. WrenchFair's published fair-price range for this repair is $40–$130 parts and $75–$180 labor at independent shops.
WrenchFair rates P0138 a 2-of-5 DIY difficulty (“Sensor access varies; an O2 socket and penetrating oil help.”) with a “Drive safe” driveability rating: Safe to drive. Fix before any catalyst diagnosis. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 454 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Engine And Engine Cooling) — see the latest ones
Emissions warranty: P0138 is emissions-related — federal law requires up to 8 years / 80,000 miles of coverage on the catalytic converter, engine computer and OBD system. Check if your repair might be free before you pay for it.
On your 2017–2022 Honda CR-V (1.5L turbo (L15BE)) — O2 (oxygen) sensors:Owner-verified
The 1.5T runs a primary wideband LAF (air/fuel ratio) sensor in the downpipe before the catalytic converter (Honda P/N 36531-5K8-004 fits all 2017–2022 CR-V 1.5T) and a secondary heated O2 sensor after the cat. Unplug the harness connector (wiring routes toward the firewall), then break the sensor loose with a 22mm slotted O2 sensor socket. The exhaust-side corrosion is the pain point: soak the bung with penetrating oil the day before, and right before the job run the engine about one minute so the thin exhaust pipe expands faster than the sensor — an owner-reported trick that freed a stuck CR-V sensor.
Do this test first: Watch the sensor voltage in scan tool live data - pinned near 1V and never moving means a dead sensor
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0138 on the 2017–2022 Honda CR-V — but the community-sourced O2 (oxygen) sensors note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
O2 sensors: verify — No Honda-published torque spec was sourced for the 1.5T LAF/AFR sensor. Confirm against factory service info before torquing; tighten snug and do not overtighten.
Tips
The upstream is a heated 5-wire wideband A/F sensor — much more expensive than the downstream narrowband; don't swap in a cheap narrowband substitute.
Check for exhaust leaks at or before the sensors first: leaks skew readings and trigger false codes, per the 2017–2019 CR-V service-manual-based guide.
Inspect sensor wiring and connectors for heat/road-grime damage during major services; intermittent faults are common there.
Confirm with a scanner before buying: P0134/P0135 point to the A/F sensor circuit/heater, P0138 to the rear O2 high voltage, P0420 to catalyst efficiency.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
failed emissions test
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed downstream O2 sensor (element or heater)
Wiring shorted to voltage / chafed harness
Contaminated sensor connector
ECM fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Watch the sensor voltage in scan tool live data - pinned near 1V and never moving means a dead sensor Tests: Wiring shorted to voltage / chafed harness
Inspect the wiring for chafing or shorts to power
Resistance-check the heater circuit
Replace the sensor; retest before any catalyst work
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2017–2022 Honda CR-V: O2 (oxygen) sensors — test first, then buy for this job.
Expensive fork: Catalytic converter — only if the downstream waveform shows a dead cat after a good sensor and no exhaust leak.
The price range below is a national planning range for P0138 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $130
Labor$75 – $180
Downstream O2 sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0138 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Sensor access varies; an O2 socket and penetrating oil help.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →