P0221

P0221 on a 2017–2022 Honda CR-V: Throttle/pedal position sensor 'B' range/performance

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0221 on a 2014–2019 Chevrolet Silverado 1500 · 2015–2020 Ford F-150 · 2017–2022 Honda CR-V · 2019–2026 Toyota Corolla · 2011–2018 Volkswagen Jetta

DIY difficulty 2/5

Your throttle's backup sensor is reading wrong - it's drifting or has a dead spot. Expect jumpy throttle response or limp mode.

Key facts

☑ Before you buy parts — check these first:
On your 2017–2022 Honda CR-V (1.5L turbo (L15BE)) — Throttle body cleaning: Owner-verified
The 1.5T uses a drive-by-wire ETCS throttle body on the intake manifold. The factory manual says to remove the throttle body to clean it — check the air cleaner for damage first, then pull the body and clean carbon from the throttle valve and bore with a paper towel soaked in throttle plate and induction cleaner. Do NOT spray cleaner directly on the throttle body, do NOT clean the bearing area of the throttle shaft (it has a molybdenum coating), and never stick fingers in the throttle body with the ignition on. Reinstall, reset the PCM, and run the PCM idle learn procedure (below). For diagnosis, the manual's carbon-accumulation check: with HDS at idle, REL TP SENSOR should read below 2.46 degrees — if higher, clean the throttle body; there's also a TP position check under the ETCS test menu.
Do this test first: Clean the throttle body thoroughly
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0221 on the 2017–2022 Honda CR-V — but the community-sourced Throttle body cleaning note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: Factory service manual — Intake Air System / Throttle Body Cleaning · Factory service manual — PCM Idle Learn Procedure · driveaccord.net forum — Honda throttle body relearn procedure (no-HDS workaround)

Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).

Typical time: “PCM idle learn is REQUIRED after cleaning or replacing the throttle body (factory procedure): all electrical items off; reset the PCM with HDS; ignition ON 2 seconds; start engine and hold 3,000 rpm no-load…” — as written in the note. First-timers often take twice this.

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0221: 5 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Clean the throttle body thoroughly Tests: Worn throttle position sensor 'B' with a dead spot (most common)
  2. Slowly sweep the throttle and watch sensors 'A' and 'B' for dropouts or jumps Tests: Worn throttle position sensor 'B' with a dead spot (most common)
  3. Check that the throttle plate moves freely Tests: Carbon-fouled throttle plate sticking
  4. Replace the throttle body if sensor 'B' has a dead spot Tests: Worn throttle position sensor 'B' with a dead spot (most common)

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2017–2022 Honda CR-V: Throttle body cleaning — test first, then buy for this job.
The price range below is a national planning range for P0221 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$100 – $400
Labor$80 – $250

Throttle body cleaning or replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0221 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Sweep-test both sensors on a scan tool - a dead spot shows as a jump.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →