P0151

P0151 on a 2015–2020 Ford F-150: O2 sensor circuit low voltage, bank 2 sensor 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0151 on a 2015–2020 Ford F-150

DIY difficulty 2/5

Your bank-2 front oxygen sensor is stuck reading lean - it could be lying (bad sensor, exhaust leak) or the engine could actually be running lean.

Key facts

☑ Before you buy parts — check these first:
On your 2015–2020 Ford F-150 (2.7L EcoBoost V6, 3.5L EcoBoost V6, 5.0L V8) — O2 (oxygen) sensors: Owner-verified
All four sensors are reached from underneath with the front raised high — upstream pair in the exhaust manifolds/downpipes, downstream pair behind the cats. Seized sensors are the known nightmare: one F150Forum owner needed an oxy/acetylene torch with the bung glowing red-hot to break one free. For stubborn front sensors, pull the passenger front wheel and wheel-well liner to get a breaker-bar angle.
Do this test first: Check for exhaust leaks ahead of the sensor
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0151 on the 2015–2020 Ford F-150 — but the community-sourced O2 (oxygen) sensors note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check for exhaust leaks ahead of the sensor Tests: Exhaust leak ahead of the sensor pulling in outside air
  2. Look for vacuum leaks or fuel delivery problems causing a real lean condition Tests: Genuine lean condition (vacuum leak, low fuel pressure)
  3. Watch the sensor voltage - stuck near 0.1V with no movement suggests a dead sensor Tests: Failed O2 sensor stuck lean (most common)
  4. Check the wiring for shorts to ground Tests: Wiring short to ground
  5. Replace the sensor if the mixture is actually fine and the wiring is good

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2015–2020 Ford F-150: O2 (oxygen) sensors — test first, then buy for this job.

Expensive fork: Catalytic converter — only if the downstream waveform shows a dead cat after a good sensor and no exhaust leak. The price range below is a national planning range for P0151 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $150
Labor$80 – $180

Upstream oxygen sensor replacement (bank 2 sensor 1) or lean-condition repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0151 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Rule out exhaust leaks and real lean conditions before replacing the sensor - the ECM adds fuel based on this reading.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: O2 sensors: typically 35–50 Nm (26–37 lb-ft) — verify spec. A dab of nickel anti-seize on the threads; keep it off the sensor tip.

Pro tip: Route the new sensor’s harness exactly like the old one — melted wires on the exhaust are the number-one comeback.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →