P0135 on a 2018–2022 Honda Accord: O2 sensor heater circuit malfunction, bank 1 sensor 1
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
DIY difficulty 2/5
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0135 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Drive safeSafe to drive. Cold-start emissions and fuel economy are affected.
Can I drive with P0135?
Can I drive with a P0135 code?
Yes. P0135 doesn't make your car unsafe to drive on its own. Safe to drive. Cold-start emissions and fuel economy are affected. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.
How serious is P0135?
Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Safe to drive. Cold-start emissions and fuel economy are affected.
Will P0135 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your oxygen sensor's built-in heater died. The car drives fine once warmed up, but cold-start fuel control suffers. Straightforward sensor swap.
VCDS tip: A blown O2 heater fuse is a $2 fix - check it first.
Model notes: Check the heater resistance across the heater pins (typically a few ohms) and the fuse before replacing the sensor. A blown fuse usually means a short elsewhere (sensor or harness) - don't just swap fuses.
Key facts
P0135 means o2 sensor heater circuit malfunction, bank 1 sensor 1. Your oxygen sensor's built-in heater died. The car drives fine once warmed up, but cold-start fuel control suffers. Straightforward sensor swap. WrenchFair's published fair-price range for this repair is $40–$200 parts and $75–$300 labor at independent shops.
WrenchFair rates P0135 a 2-of-5 DIY difficulty (“Straightforward sensor swap.”) with a “Drive safe” driveability rating: Safe to drive. Cold-start emissions and fuel economy are affected. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 394 factory bulletins on file for this vehicle (mostly Electrical System, Fuel System, Gasoline, Engine And Engine Cooling) — see the latest ones
Emissions warranty: P0135 is emissions-related — federal law requires up to 8 years / 80,000 miles of coverage on the catalytic converter, engine computer and OBD system. Check if your repair might be free before you pay for it.
On your 2018–2022 Honda Accord (1.5L turbo (L15BE), 2.0L turbo (K20C4)) — O2 (oxygen) sensors:Owner-verified
The 10th gen runs four O2 sensors on both the 1.5T and 2.0T: two upstream (pre-cat) near the exhaust manifold/turbo outlet and two downstream after the catalytic converter. All are easiest to reach from underneath on ramps or jack stands with a slotted O2 sensor socket; trace each sensor's harness and mark its connector before unplugging so the four connectors don't get mixed up.
Do this test first: Check heater resistance across the heater pins (typically a few ohms)
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0135 on the 2018–2022 Honda Accord — but the community-sourced O2 (oxygen) sensors note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
O2 sensors: verify — Confirm against factory service info for this engine before torquing.
Tips
Identify the correct sensor (upstream vs downstream, bank 1) before buying — the walkthrough maps all four positions on both turbo engines.
Soak the sensor threads with penetrating oil well before removal; heat-seized sensors are the main failure point of the job.
Use a proper slotted 22mm O2 sensor socket so the sensor pigtail passes through — an open-end wrench rounds the hex on tight sensors.
The walkthrough specifically warns that swapping sensor connectors during reassembly can trigger a check engine light, so label each connector as you disconnect it.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
slow warm-up fuel trim correction
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Burned-out heater element in the sensor 6 owner notes link this repair to P0135
Blown fuse
Wiring fault
Owner notes linked to P0135: 6 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check heater resistance across the heater pins (typically a few ohms)
Check the fuse
Most likely job on your 2018–2022 Honda Accord: O2 (oxygen) sensors — test first, then buy for this job.
Expensive fork: Catalytic converter — only if the downstream waveform shows a dead cat after a good sensor and no exhaust leak.
The price range below is a national planning range for P0135 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $200
Labor$75 – $300
The sensor itself runs $20-$200 for the part (OEM-quality to $200); shop totals run $150-$400, up to ~$470 for hard-to-reach sensors. DIY is about $85 in parts. Match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →