P0138: O2 sensor circuit high voltage, bank 1 sensor 2
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Drive safeEmissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever.
The downstream (post-cat) O2 sensor signal is stuck high. This is a circuit/sensor fault - usually the sensor itself or wiring shorted to power - not a catalyst diagnosis. Do not condemn the cat on this code.
VW/Audi note (VCDS): A downstream sensor pinned near 1V that never switches is dead - replace it, then evaluate the cat.
Model notes: Jetta 1.4T at high mileage: the downstream sensor is a consumable at this mileage - replace on principle if original. Fix this before trusting any P0420 catalyst reading, since cat monitoring depends on this sensor.
Key facts
P0138 means o2 sensor circuit high voltage, bank 1 sensor 2. The downstream (post-cat) O2 sensor signal is stuck high. This is a circuit/sensor fault - usually the sensor itself or wiring shorted to power - not a catalyst diagnosis. Do not condemn the cat on this code. WrenchFair's published fair-price range for this repair is $40–$130 parts and $75–$180 labor at independent shops.
WrenchFair rates P0138 a 2-of-5 DIY difficulty (“Sensor access varies; an O2 socket and penetrating oil help.”) with a “Drive safe” driveability rating: Emissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
failed emissions test
Likely causes
Failed downstream O2 sensor (element or heater)
Wiring shorted to voltage / chafed harness
Contaminated sensor connector
ECM fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Watch the sensor voltage in VCDS measuring blocks - pinned near 1V and never moving means a dead sensor Tests: Wiring shorted to voltage / chafed harness
Inspect the wiring for chafing or shorts to power
Resistance-check the heater circuit
Replace the sensor; retest before any catalyst work
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $130
Labor$75 – $180
O2 sensor replacement is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0138-VAG ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Sensor access varies; an O2 socket and penetrating oil help.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →