2018–2022 Honda Accord

Community-sourced DIY repair guides for the 2018–2022 Honda Accord, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.

Owner-verified repair guides

Spark plugs & ignition coils Owner-verified (1.5L turbo (L15BE), 2.0L turbo (K20C4))

Pull the hard plastic engine cover straight up off its mounts to expose the four coil packs on top of the valve cover; disconnect each coil's electrical connector and remove its 10mm hold-down bolt, then lift the coils out to reach the plugs down in the wells. Remove/install plugs with a 14mm thin-wall spark plug socket and an extension. The coil wells collect grit — blow them out with compressed air before pulling the plugs, and release the brittle plastic coil-connector locking tabs gently.

Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide

P0300 on this Honda Accord — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

O2 (oxygen) sensors Owner-verified (1.5L turbo (L15BE), 2.0L turbo (K20C4))

The 10th gen runs four O2 sensors on both the 1.5T and 2.0T: two upstream (pre-cat) near the exhaust manifold/turbo outlet and two downstream after the catalytic converter. All are easiest to reach from underneath on ramps or jack stands with a slotted O2 sensor socket; trace each sensor's harness and mark its connector before unplugging so the four connectors don't get mixed up.

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide

P0135 on this Honda Accord — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Thermostat replacement Owner-verified (1.5L turbo (L15BE))

On the 1.5T the thermostat is buried at the front of the engine next to the water pump, so per the full-length 2018 1.5T walkthrough you must remove the serpentine belt and move aside surrounding accessories to reach it (thermostat disassembly begins ~42 min into the video, after the water-pump section). The thermostat is an integrated water-outlet housing assembly — buy the complete assembly (thermostat + gasket + housing), not a loose thermostat.

Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).

Typical time: “On the 1.5T the thermostat is buried at the front of the engine next to the water pump, so per the full-length 2018 1.5T walkthrough you must remove the serpentine belt and move aside surrounding accessories to reach it…” — as written in the note. First-timers often take twice this.

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide

P0128 on this Honda Accord — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Front brake pads & rotors Owner-verified (1.5L turbo (L15BE))

Front brakes are conventional floating-caliper single-piston (no EPB involvement on the front; the rear axle has an electronic parking brake that must be put in maintenance mode before servicing the rear). Remove the front wheel, then remove the two caliper guide-pin bolts and swing/hang the caliper off the bracket (do not hang it by the brake hose). Remove the two caliper bracket bolts to free the bracket. The rotor is held by Honda's two small set screws (JIS — not Phillips — heads): use an impact screwdriver with a #3 bit set to counter-clockwise, or carefully chisel the heads free if corroded. Replace the screws on reassembly (they center the rotor on the studs); rust-belt cars often have them fused — anti-seize on new screws helps next time. Clean and regrease the slide pins with high-temp caliper grease during service. Pump the brake pedal to seat the pads before driving.

Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: YouTube: 2018-2022 Accord front & rear brake pads/rotors step-by-step DIY (impact screwdriver on rotor screws, pin service, EPB maintenance mode for rear) · driveaccord.net: rotor set-screw debate (JIS heads, 7.2 ft-lb Honda manual value, knocking noise when screws omitted) · odyclub/driveaccord owners: Accord wheel lug nuts torqued to 80 ft-lb · NAPA brake pad break-in/bedding bulletin (15 stops 35-40 mph, 30-sec cooling, avoid hard braking 200 mi)

C0035 on this Honda Accord — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Battery replacement Owner-verified (1.5L turbo (L15BE))

The 12V battery sits under the front hood in the engine bay (Honda emergency-response guide confirms conventional 12V battery location under the hood). Engine off: loosen and remove the black negative cable first, then the red positive cable (twist-and-pull, don't pry with metal tools). Remove the tie-down/hold-down clamp bolt(s) with a wrench or ratchet, then lift the battery out (heavy). Clean the tray and cable corrosion with a wire brush before installing the new battery; reverse the steps to reinstall. 10th-gen Accords have no anti-theft radio code — after a power loss the audio system shows a power-loss prompt; press and hold the power/volume knob for ~2 seconds to reinitialize it. Expect a cluster of dash warning lights (VSA/ABS/traction etc.) after reconnect; they clear on their own after 1-2 drives, and steering-angle relearn happens automatically as you drive. Reset the clock and the driver's power-window auto up/down: with ignition ON and window fully up, hold the down switch until the window bottoms out and keep holding ~2 seconds, release, then hold the up switch until fully closed and keep holding ~2 seconds. Honda idle relearn after the battery reset: with all electrical loads off, hold the engine at 3000 rpm until the radiator fan cycles on, release the accelerator, then let it idle undisturbed for ~5 minutes.

Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).

Typical time: “Honda idle relearn after the battery reset: with all electrical loads off, hold the engine at 3000 rpm until the radiator fan cycles on, release the accelerator, then let it idle undisturbed for ~5 minutes.” — as written in the note. First-timers often take twice this.

Torque specs

Tips

Sources: Honda Canada: 2018-20 Accord Emergency Response Guide (12V battery under front hood) · McDavid Honda Frisco: 2018 Accord battery replacement steps (negative cable first, hold-down clamp removal, tray cleaning) · YouTube: DIY 2018-2022 Accord battery replacement walkthrough · civicx.com: battery disconnect on 10th-gen Honda platform (no radio code, hold power button 2s, dash lights clear after 1-2 drives, automatic steering relearn) · driveaccord.net: power-window auto up/down reset procedure after battery disconnect (hold down 2s at bottom, hold up 2s at top) · team-bhp: Honda idle relearn from Honda manual (3000 rpm to fan cycle, then 5-min idle, loads off)

P0560 on this Honda Accord — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Fuel pump replacement Owner-verified (1.5L turbo (L15BE))

The fuel pump is serviced from inside the car — no tank drop needed; dealers confirm access is under the rear seat/carpet. Remove the trunk floor cover, fold the rear seatbacks down, pull the seatback cover aside and remove the retaining bolt, then push the seat cushion down while pulling the seat-hook handles to release it (disconnect seat-heater connectors if equipped). Under the cushion is the fuel tank unit access panel; remove it, disconnect the electrical connector and the fuel quick-connect (wrap the fitting in a rag — fuel will spray). Unlock the pump cam lock ring counterclockwise with the Honda fuel sender wrench (part 070AA-TLA0100 in the official procedure), lift the pump unit out, and clean the flange area before installing the new unit with a fresh O-ring. The official Honda repair procedure also calls for a VSA sensor neutral-position memorization after the job.

Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: NHTSA recall bulletin — official Honda fuel pump motor repair procedure (2018-19 Accord) · accordxclub thread — dealer confirms under-rear-seat access, no tank drop

P0087 on this Honda Accord — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Throttle body cleaning Owner-verified (1.5L turbo (L15BE))

Cleaning the throttle body on a 10th-gen Accord is straightforward — the make-or-break step is Honda's idle relearn afterward, which owners confirm is mandatory: skip it and the car idles around 1,500 rpm. The driveaccord-verified procedure: disconnect both battery cables, jumper the cables together for 10 minutes to fully drain the vehicle's capacitors (keep the cables off the battery terminals), then reconnect. Start the engine with EVERY load off — no AC, no lights, no accessories — and let it idle without touching the throttle until the cooling fans cycle twice; Honda's own guidance is about 15 minutes for the idle learn. Mark a fan blade with a Sharpie before starting so you can walk away and confirm the fans actually ran. A Honda-manual variant of the same relearn adds: with loads off, hold 3,000 rpm until the radiator fans start, then release the pedal and idle 5 minutes.

Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).

Typical time: “The driveaccord-verified procedure: disconnect both battery cables, jumper the cables together for 10 minutes to fully drain the vehicle's capacitors (keep the cables off the battery terminals), then reconnect.” — as written in the note. First-timers often take twice this.

Torque specs

Tips

Sources: driveaccord thread — throttle body idle relearn procedure, owner-confirmed fix · team-bhp thread — Honda-manual idle relearn steps quoted verbatim

No owner reports yet — fixed this yourself? tell us how

CVT fluid service Owner-verified (1.5L turbo (L15BE))

The 1.5T pairs with a Honda CVT (no dipstick) serviced by drain & fill. Raise the car LEVEL and remove the underbody splash shield — the drain plug is clearly marked, and the 12mm check bolt sits just above it on the case. Drain, reinstall the drain plug with a new crush washer, and refill through the top fill port with a funnel or hand pump using Honda HCF-2 fluid ONLY (part 08200-HCF2; the wrong fluid damages the CVT). Set the level on flat ground with the engine OFF after cycling the shifter through every position (~3 seconds each) and returning to Park: remove the check bolt and fill until fluid slows to a drip, then reinstall with a new gasket. No filter is serviceable per Honda — dealers do drain & fill only, and the maintenance minder calls the CVT service around ~50k miles; never power-flush the unit.

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: YouTube — Honda Accord Transmission Fluid Change CVT, 2018 Honda Accord 1.5T (BoostedFilms) · YouTube — 2018 Honda Accord CVT fluid change, HCF-2 part numbers (Stumph) · YouTube — Accord CVT fluid replacement, drain-plug and check-bolt torque + level-check method · bogleheads thread — CVT check-bolt method and maintenance-minder interval · bobistheoilguy thread — Honda dealer drain-and-fill-only practice, internal filter discussion · YouTube — Honda CVT warmer/filter cartridge replacement, 2013-2021 Accords (DIYautoWorks)

P0700 on this Honda Accord — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

1.5T head gasket failure (10yr/150k warranty extension) Factory-documented (1.5L turbo (L15BE))

No DIY teardown - this is a diagnose-and-claim note. A head gasket job is shop-only, but under Honda's September 2026 extended coverage it is FREE at the dealer for qualifying vehicles: check your VIN with a dealer before authorizing any paid repair.

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

Tips

Sources: AutoGuide - Honda extends head gasket warranty to 10 years / 150,000 miles (Sep 2026) · Torque News - Honda head gasket warranty extension, May 2027 grace period · Autoblog - Accord bulletin numbers 26-003 through 26-007, DTCs P0300-P0304 · DriveAccord owner forum - 2018 Accord 1.5T head gasket failure reports (P0303, hydrocarbons in coolant) · Torque News - 2020 Accord 1.5T head gasket failure at 49,000 miles (owner story)

No owner reports yet — fixed this yourself? tell us how

1.5T oil dilution (fuel in oil) Owner-verified (1.5L turbo (L15BE))

No teardown for the checks - dipstick monitoring and oil changes only. The dipstick is the instrument: check the level regularly and watch for a rising level or strong fuel smell.

Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: DriveAccord owner forum - 10th-gen Accord 1.5T fuel-in-oil reports (rising level, gas smell on dipstick) · SlashGear - Honda engines with oil dilution problems; class action names 2018-2023 Accord 1.5T

No owner reports yet — fixed this yourself? tell us how

Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

DIY-friendliness scorecard

Score: 93/100 — DIY-friendly

How this is scored (mechanical, no opinion): start at 100; −4 per distinct special tool mentioned in the notes (max −28); −15 per documented dealer-only step (max −30); note-volume band: 15+ notes +10, 8–14 +5, 4–7 +0. Bands: 85+ DIY-friendly · 65–84 DIY with care · 40–64 Experienced DIY only · below 40 Think twice. Pilot rubric — flagged for Robbie’s eyeball before any scale-up.

Codes on this Accord

C0035
2018–2022 Honda Accord
Front brake pads & rotors
C0040
2018–2022 Honda Accord
Front brake pads & rotors
C0045
2018–2022 Honda Accord
Front brake pads & rotors
P0087
2018–2022 Honda Accord
Fuel pump replacement
P0117
2018–2022 Honda Accord
Thermostat replacement
P0118
2018–2022 Honda Accord
Thermostat replacement
P0121
2018–2022 Honda Accord
Throttle body cleaning
P0128
2018–2022 Honda Accord
Thermostat replacement
P0131
2018–2022 Honda Accord
O2 (oxygen) sensors
P0135
2018–2022 Honda Accord
O2 (oxygen) sensors
P0137
2018–2022 Honda Accord
O2 (oxygen) sensors
P0141
2018–2022 Honda Accord
O2 (oxygen) sensors
P0191
2018–2022 Honda Accord
Fuel pump replacement
P0231
2018–2022 Honda Accord
Fuel pump replacement
P0300
2018–2022 Honda Accord
Spark plugs & ignition coils
P0301
2018–2022 Honda Accord
Spark plugs & ignition coils
P0302
2018–2022 Honda Accord
Spark plugs & ignition coils
P0303
2018–2022 Honda Accord
Spark plugs & ignition coils
P0304
2018–2022 Honda Accord
Spark plugs & ignition coils
P0463
2018–2022 Honda Accord
Fuel pump replacement
P0507
2018–2022 Honda Accord
Throttle body cleaning
P0560
2018–2022 Honda Accord
Battery replacement
P0562
2018–2022 Honda Accord
Battery replacement
P0563
2018–2022 Honda Accord
Battery replacement
P0700
2018–2022 Honda Accord
CVT fluid service
P0730
2018–2022 Honda Accord
CVT fluid service
P0741
2018–2022 Honda Accord
CVT fluid service
P0780
2018–2022 Honda Accord
CVT fluid service

What owners report

NHTSA recorded 362 complaints for the 2018–2022 Honda Accord. 2020 was the worst year (362 complaints). Most-reported areas: forward collision avoidance, engine, service brakes.

Counts are NHTSA complaints filed for these model years, via the NHTSA API. See data for all Accord years →

Recalls

5 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.

Factory service bulletins

NHTSA has published 394 manufacturer communications (service bulletins, dealer notices) covering the 2018–2022 Honda Accord.

Most cited systems: Electrical System (92), Fuel System, Gasoline (64), Engine And Engine Cooling (56), Service Brakes, Hydraulic (47), Equipment (43).

Latest bulletins:

NHTSA also opened 2 defect investigations covering these years.

Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.

Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.