P0137

P0137 on a 2018–2022 Honda Accord: O2 sensor circuit low voltage, bank 1 sensor 2

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0137 on a 2018–2022 Honda Accord · 2019–2024 Toyota RAV4

DIY difficulty 2/5

Can I drive with P0137?

Can I drive with a P0137 code?

Yes. P0137 doesn't make your car unsafe to drive on its own. Emissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.

How serious is P0137?

Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Emissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever.

Will P0137 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

The sensor behind your catalytic converter is reading too much oxygen in the exhaust. Usually that means a small exhaust leak is letting outside air in near the sensor.

Model notes: Exhaust leaks are the number-one cause and the cheapest fix - a $5 gasket beats a $500 converter. Listen for ticking at the manifold on cold start.

Key facts

☑ Before you buy parts — check these first:
On your 2018–2022 Honda Accord (1.5L turbo (L15BE), 2.0L turbo (K20C4)) — O2 (oxygen) sensors: Owner-verified
The 10th gen runs four O2 sensors on both the 1.5T and 2.0T: two upstream (pre-cat) near the exhaust manifold/turbo outlet and two downstream after the catalytic converter. All are easiest to reach from underneath on ramps or jack stands with a slotted O2 sensor socket; trace each sensor's harness and mark its connector before unplugging so the four connectors don't get mixed up.
Do this test first: Inspect the exhaust from the manifold to past the downstream sensor for leaks - even a pinhole ahead of the sensor sets this code
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0137 on the 2018–2022 Honda Accord — but the community-sourced O2 (oxygen) sensors note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: owner forum / guide · owner forum / guide

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0137: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Inspect the exhaust from the manifold to past the downstream sensor for leaks - even a pinhole ahead of the sensor sets this code Tests: Exhaust leak upstream of or near the downstream sensor pulling in air (very common)
  2. Check fuel trims: if long-term trims are high positive, fix the lean condition first Tests: Vacuum leak or lean running condition flooding the exhaust with oxygen
  3. If no leaks and trims are normal, the sensor or the converter is suspect - compare sensor behavior before replacing either Tests: Exhaust leak upstream of or near the downstream sensor pulling in air (very common)
  4. Do not replace the converter until leaks and the sensor are ruled out - converters are expensive Tests: Exhaust leak upstream of or near the downstream sensor pulling in air (very common)

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2018–2022 Honda Accord: O2 (oxygen) sensors — test first, then buy for this job.

Expensive fork: Catalytic converter — only if the downstream waveform shows a dead cat after a good sensor and no exhaust leak. The price range below is a national planning range for P0137 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $130
Labor$75 – $180

O2 sensor replacement is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0137 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — The code is easy to read; the skill is deciding between an exhaust leak, a bad sensor, and a dead converter.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: O2 sensors: typically 35–50 Nm (26–37 lb-ft) — verify spec. A dab of nickel anti-seize on the threads; keep it off the sensor tip.

Pro tip: Route the new sensor’s harness exactly like the old one — melted wires on the exhaust are the number-one comeback.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →