P0135

P0135: O2 sensor heater circuit malfunction, bank 1 sensor 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

DIY difficulty 2/5

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0135 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

At a glance

What it meansYour oxygen sensor's built-in heater died. The car drives fine once warmed up, but cold-start fuel control suffers. Straightforward sensor swap.
Most common causeBurned-out heater element in the sensor
Can you drive?Yes.
SeverityLow
DIY cost (parts only)$40 – $200
Shop cost (parts + labor)$115 – $500
DIY difficulty2 of 5 — Straightforward sensor swap.

Can I drive with P0135?

Can I drive with a P0135 code?

Yes. P0135 doesn't make your car unsafe to drive on its own. Safe to drive. Cold-start emissions and fuel economy are affected. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.

How serious is P0135?

Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Safe to drive. Cold-start emissions and fuel economy are affected.

Will P0135 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

More detail: can I drive with P0135? →

Your oxygen sensor's built-in heater died. The car drives fine once warmed up, but cold-start fuel control suffers. Straightforward sensor swap.

VCDS tip: A blown O2 heater fuse is a $2 fix - check it first.
Model notes: Check the heater resistance across the heater pins (typically a few ohms) and the fuse before replacing the sensor. A blown fuse usually means a short elsewhere (sensor or harness) - don't just swap fuses.

Key facts

Symptoms

Likely causes

Owner notes linked to P0135: 6 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 2 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check heater resistance across the heater pins (typically a few ohms)
  2. Check the fuse

Typical price range

Parts$40 – $200
Labor$75 – $300

The sensor itself runs $20-$200 for the part (OEM-quality to $200); shop totals run $150-$400, up to ~$470 for hard-to-reach sensors. DIY is about $85 in parts. Match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

DIY difficulty

2 of 5 — Straightforward sensor swap.

Parts & tools

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →