P010C

P010C on a 2014–2020 Ram 3500: MAF sensor 'B' circuit low

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P010C on a 2014–2020 Ram 3500

DIY difficulty 2/5

Your second airflow sensor is reading too low - it's dirty, unplugged, or has a wiring fault. The engine may run lean.

Key facts

☑ Before you buy parts — check these first:
On your 2014–2020 Ram 3500 (6.7L Cummins Turbo Diesel) — P0299 underboost / VGT actuator failure: Owner-verified
Driveway diagnosis — check the air filter, CAC hoses, and MAP sensor first. The actuator itself is a bolt-on part but must be calibrated to the turbo with a scan tool afterward.
Do this test first: Verify the 'B' MAF connector is fully seated
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P010C on the 2014–2020 Ram 3500 — but the community-sourced P0299 underboost / VGT actuator failure note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: repair guide · owner forum · owner forum · owner forum

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Verify the 'B' MAF connector is fully seated Tests: Unplugged 'B' MAF connector
  2. Clean the sensor with dedicated cleaner
  3. Compare 'A' and 'B' readings
  4. Check the wiring for faults Tests: Wiring fault pulling the signal low
  5. Replace the 'B' sensor if it reads low when clean and connected

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2014–2020 Ram 3500: P0299 underboost / VGT actuator failure — test first, then buy for this job.
The price range below is a national planning range for P010C on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$60 – $250
Labor$80 – $200

MAF sensor 'B' cleaning or replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P010C ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Check the connector first, then clean the sensor.

Watch this repair on YouTube

Parts & tools

Intake & throttle toolkit — what the job actually takes

Torque specs: Throttle body bolts: typically 8–12 Nm — verify spec.

Pro tip: Some cars need a throttle relearn after cleaning (scan tool or battery-disconnect procedure), or the idle will hunt.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →