Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonBad air measurement causes poor running and possible limp mode. Drive gently.
The sensor measuring how much air enters the engine has an electrical problem, so the computer has to guess at fueling and the car runs rough. Try cleaning the sensor first - it's a 10-minute job that fixes this more often than not.
VW/Audi note (VCDS): The g/s at idle vs engine displacement rule of thumb catches most MAF faults in seconds without any disassembly.
Model notes: Oiled cotton air filters are the number-one MAF killer in the DIY world - oil mist coats the sensing wires. If you run one, clean the MAF at every filter service.
Key facts
P0100 means mass airflow sensor circuit malfunction. The sensor measuring how much air enters the engine has an electrical problem, so the computer has to guess at fueling and the car runs rough. Try cleaning the sensor first - it's a 10-minute job that fixes this more often than not. WrenchFair's published fair-price range for this repair is $10–$250 parts and $50–$150 labor at independent shops.
WrenchFair rates P0100 a 1-of-5 DIY difficulty (“Try cleaning before replacing - contaminated MAF wires are the most common cause and cleaning is a 10-minute job.”) with a “Diagnose soon” driveability rating: Bad air measurement causes poor running and possible limp mode. Drive gently. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
rough idle
hesitation
stalling
poor fuel economy
black smoke if running rich on backup maps
hard starting
Likely causes
Failed MAF sensor (most common)
Contaminated MAF sensing wires from oiled air filters or dirt
Damaged wiring or connector
Air intake leak between the MAF and the throttle body (unmetered air)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Inspect the air intake tract for cracks or loose clamps between the MAF and throttle - leaks here cause false readings Tests: Air intake leak between the MAF and the throttle body (unmetered air)
Remove and inspect the MAF sensing wires; clean with dedicated MAF cleaner only, never touch the wires Tests: Contaminated MAF sensing wires from oiled air filters or dirt
Check live data: MAF grams/second at warm idle should roughly match engine displacement in liters (e.g., ~3 g/s for a 3.0L)
If cleaning and intake inspection do not help, test the wiring, then replace the sensor
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$10 – $250
Labor$50 – $150
Cleaning is cheap; sensor replacement costs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0100 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
1 of 5 — Try cleaning before replacing - contaminated MAF wires are the most common cause and cleaning is a 10-minute job.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →