P0110: Intake air temperature sensor circuit malfunction
DIY difficulty 1/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonBad air measurement causes poor running and possible limp mode. Drive gently.
The sensor measuring the temperature of incoming air has an electrical fault. It's a minor input, but without it the computer can't fine-tune fueling for hot or cold weather.
VW/Audi note (VCDS): The cold-soak comparison (IAT vs ambient before startup) is the definitive IAT rationality test.
Model notes: On many vehicles the IAT sensor is built into the MAF sensor - a failed IAT means replacing the whole MAF assembly on those designs.
Key facts
P0110 means intake air temperature sensor circuit malfunction. The sensor measuring the temperature of incoming air has an electrical fault. It's a minor input, but without it the computer can't fine-tune fueling for hot or cold weather. WrenchFair's published fair-price range for this repair is $10–$250 parts and $50–$150 labor at independent shops.
WrenchFair rates P0110 a 1-of-5 DIY difficulty (“One of the simplest sensors to test and replace - often part of the MAF assembly.”) with a “Diagnose soon” driveability rating: Bad air measurement causes poor running and possible limp mode. Drive gently. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
slightly off fuel economy
possible hard starting in extreme cold or heat
Likely causes
Failed IAT sensor (most common - often integrated into the MAF)
Damaged wiring or connector
Corroded terminals
Sensor contaminated with oil from an oiled air filter
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Compare IAT reading to ambient temperature on a cold engine - they should match within a few degrees
Check the connector and wiring Tests: Damaged wiring or connector
Test sensor resistance against the temperature/resistance chart if available
Clean oil contamination if an oiled filter is fitted Tests: Sensor contaminated with oil from an oiled air filter
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$10 – $250
Labor$50 – $150
Cleaning is cheap; sensor replacement costs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0110 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
1 of 5 — One of the simplest sensors to test and replace - often part of the MAF assembly.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →