Diagnose soonThe engine may not start or could stall without warning — do not drive it until this is fixed; plan on a tow.
Your car's computers all chat over a shared wiring network. Right now, the fuel pump control module — the part that handles fuel delivery — has stopped answering. The engine may not start or may stall. Check the simple stuff first: a blown fuse or a loose, corroded connector is a far more common cause than a dead module.
Key facts
U0109 means lost communication with Fuel pump control module. Your car's computers all chat over a shared wiring network. Right now, the fuel pump control module — the part that handles fuel delivery — has stopped answering. The engine may not start or may stall. Check the simple stuff first: a blown fuse or a loose, corroded connector is a far more common cause than a dead module. WrenchFair's published fair-price range for this repair is $0–$600 parts and $120–$300 labor at independent shops.
WrenchFair rates U0109 a 2-of-5 DIY difficulty (“Finding a blown fuse or bad connector is easy; tracing bus wiring to the module is the part that takes patience.”) with a “Diagnose soon” driveability rating: The engine may not start or could stall without warning — do not drive it until this is fixed; plan on a tow. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2007–2014 Chevrolet Tahoe (5.3L V8, 6.2L V8) — Fuel pump control module water intrusion (stall):Owner-verified
The fuel pump control module sits underneath the truck near the spare tire, exposed to road spray. It is a sealed plastic box with an RTV gasket — when that seal separates, water gets inside. The module is secured with bolts that are often heavily rusted.
Do this test first: Read all codes with a scan tool. This code is set by a listening module, not the silent one — note any companion codes naming other offline modules or bus faults, which point at shared power or wiring instead of one bad module.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for U0109 on the 2007–2014 Chevrolet Tahoe — but the community-sourced Fuel pump control module water intrusion (stall) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Fuel pump control module fasteners: verify — Fastener torque not confirmed from a forum source — confirm against factory service info. The module bolts are often rusted; penetrating oil and patience beat snapping them off.
Tips
Know the signature symptom: the engine stalls on turns — one owner's 2009 Tahoe died on every right turn. Water pooled inside the module sloshes during the turn and shorts the fuel pump circuit. If stalling correlates with cornering, this is the prime suspect.
Scan first: codes P069E (FPCM requested MIL), P025A (FPCM control circuit open), P0230, or U0109 (lost communication with FPCM) all point here. One owner logged fuel pressure dropping to 0 PSI on every right turn — that is the telltale.
Do the tilt test before buying parts: with the engine running, unbolt the module and tilt it one way, then the other. If tilting reproduces the stall, the module has water inside. The solved case owner found about a shot glass of water poured out when the module was opened.
The recall context: GM recalled 2009 trucks (27,188 vehicles including Tahoe) for RTV seal separation letting water seep into the module. Even outside the recall, the fix is the same — replace the module, and consider relocating it or adding protection so road spray cannot reach it again.
Do not jump straight to the fuel pump in the tank. If pressure reads normally on a scan tool except during the stall event, the pump itself is fine — it is the control module cutting power.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
fuel delivery not working
warning light on the dash (check engine, abs, or a module-specific message)
related features dead, intermittent, or stuck
companion communication codes stored in other modules
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Blown fuse or corroded fuse holder feeding the fuel pump control module (most common easy fix — check the fuses first)
Loose, corroded, or water-damaged connector at the fuel pump control module
Chafed, pinched, or broken data-bus wiring running to the fuel pump control module
Aftermarket device tapped into the data bus (remote starter, alarm, fleet tracker, plug-in insurance dongle)
The fuel pump control module failed internally (possible but uncommon — rule out power and wiring first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read all codes with a scan tool. This code is set by a listening module, not the silent one — note any companion codes naming other offline modules or bus faults, which point at shared power or wiring instead of one bad module. Tests: The fuel pump control module failed internally (possible but uncommon — rule out power…
Check the fuses for the fuel pump control module using the owner's manual fuse chart. A blown, corroded, or loose fuse is the cheapest possible cause — don't skip this step. Tests: Blown fuse or corroded fuse holder feeding the fuel pump control module (most common easy…
Unplug the connector at the fuel pump control module and verify its power and ground with a multimeter. Look closely for green corrosion, backed-out pins, or water inside the connector — most 'dead module' diagnoses turn out to be bad connections. Tests: Loose, corroded, or water-damaged connector at the fuel pump control module
Trace the data-bus wiring to the fuel pump control module: look for chafed or pinched harness runs, water intrusion at connectors, and aftermarket devices (alarms, remote starters, trackers) tapped into the bus. Tests: Chafed, pinched, or broken data-bus wiring running to the fuel pump control module
If power, ground, and wiring all check out, the module itself may have failed — but replacement modules usually need programming to the vehicle, so confirm the wiring first and get a second opinion before buying one.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2014 Chevrolet Tahoe: Fuel pump control module water intrusion (stall) — test first, then buy for this job.
The price range below is a national planning range for U0109 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$0 – $600
Labor$120 – $300
Blown fuse or wiring repair (most common). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U0109 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Finding a blown fuse or bad connector is easy; tracing bus wiring to the module is the part that takes patience.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →