P2EAC: Active Radiator Air Flow Control Module A Performance
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonStuck-closed shutters can overheat the engine in traffic - check that they open before a hot drive.
The active grille shutters in front of your radiator - which open and close for warm-up and aerodynamics - are reporting a fault in their control module.
Key facts
P2EAC means active Radiator Air Flow Control Module A Performance. The active grille shutters in front of your radiator - which open and close for warm-up and aerodynamics - are reporting a fault in their control module. WrenchFair's published fair-price range for this repair is $150–$500 parts and $150–$350 labor at independent shops.
WrenchFair rates P2EAC a 2-of-5 DIY difficulty (“Most fixes are clearing debris or freeing a slat; the bumper sometimes has to come off for module access.”) with a “Diagnose soon” driveability rating: Stuck-closed shutters can overheat the engine in traffic - check that they open before a hot drive. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
shutters visibly stuck open or closed
engine running hotter than normal
slightly worse highway fuel economy (stuck open)
Likely causes
Jammed, iced, or debris-blocked shutter slats (most common)
Failed shutter actuator motor
Failed shutter control module
Corroded connector or damaged wiring
shutter actuator lazy
linkage iced
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Visually inspect the shutters for ice, debris, bent slats, or a stuck motor linkage. Tests: Jammed, iced, or debris-blocked shutter slats (most common)
Command the shutters with a scan tool and watch them move through their full travel. Tests: Jammed, iced, or debris-blocked shutter slats (most common)
Check the shutter module's power, ground, and connector for corrosion. Tests: Jammed, iced, or debris-blocked shutter slats (most common)
Free or straighten jammed slats; replace the actuator or module if it will not drive them. Tests: Jammed, iced, or debris-blocked shutter slats (most common)
Verify full travel and recheck for codes after a drive cycle.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$150 – $500
Labor$150 – $350
Active grille shutter actuator or control module replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2EAC ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Most fixes are clearing debris or freeing a slat; the bumper sometimes has to come off for module access.
Torque specs: Thermostat housing bolts: typically 8–12 Nm. Aluminum threads strip easily — verify spec and use a torque wrench.
Pro tip: Bleed the cooling system per the factory procedure after refilling, or trapped air will overheat the engine and fake a “still broken” reading.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →